SHOP! Le Salon covers point-of-sale displays, furniture, lighting and LEDs. Plan how an installer can reach internal lightbox components within the retail fixture. Browse the full LED Modules range below.
Prove access with the fixture assembled
Mark the removable graphic or service panel and the power-isolation point. Trial the intended tool, screw access and module-removal route without moving shelves or damaging furniture. Keep connector access and cable clearance visible in the approved section drawing; a short bar alone does not prove serviceability.
Place the cable exit within the service opening
The profile family has a 40.7mm-wide, 17mm-high housing. Its standard 32cm lead exits at the left end on the bottom side; confirm another exit before ordering. Trial the chosen module and mating cable in the fixture. Accessible DC sockets still need a verified plug, pinout and polarity.
Compare LED lightbox sources
- 7W mini edge-lit bar: 200×23×16mm, DC24V, 770lm and standard 20°×60° optics; verify available mounting and removal space.
- 10W DC-plug edge-lit bar: 360×26×16mm including lens, DC24V, 1000lm ±10%, 15°×45° optics and dual-end DC sockets.
- Aluminum-profile edge-lit family: 22W/25W/32W, DC24V, 40.7×17mm housing and 14°×47° optics; specify length and wire exit.
Can a removable graphic replace a service-access check?
No. Confirm that the module, fasteners and cable can actually be reached and removed through that opening. Save the approved route and model before repeat fabrication.
Before ordering
These are internal light sources, not complete retail fixtures. Disconnect power before service. Verify DC24V, load, connector pinout and polarity; confirm power and hardware separately. The featured 10W DC-plug bar permits at most 6 per run after wiring checks. Do not transfer the limit to other models.
Send the fixture section, service-opening dimensions, removal-route photos, cable-exit requirement and quantity through our contact page for a component-access review.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
-
7W 200mm Mini LED Light Box Bar – 770lm, DC24V -
10W DC Plug LED Lightbox Bar – 360mm, 24V, 15°×45° Optical Lens -
22W–32W Aluminum Profile LED Lightbox Modules – 10-Pack+ -
10W Slim Edge-Lit LED Lightbox Bar – 360mm, 9°×50° Lens -
20W Rigid LED Light Box Bars – 2200lm, DC24V, 10-Pack+ -
Flexible LED Stone Backlight Panel – 480×240mm, 24W/48W -
FOGA SYSTEM 10W LED Module – Edge-Lit Lightbox Bar -
12W Dual-CCT Switchable LED Lightbox Bar – 24V -
13W Edge-Lit LED Lightbox Bar – 360mm, 1430lm, ETL Listed -
7W DC24V Side-Lit LED Lightbox Module – Optical Lens -
Side-Lit LED Module for MODULAP Systems -
12W/18W LED Module for MODULAP Fabric Lightbox -
24W RGB Edge-Lit LED Bar for SEG Light Boxes & Displays -
32W 4-in-1 RGBW Edge-Lit LED Light Box Bars – 10-Pack+ -
14W 313mm-Long Edge-Lit LED Light Box Bars – 1540lm -
DC24V Linkable Edge-Lit LED Light Box Bars for SEG Displays -
27.5W Optical Edge-Lit LED Light Box Bars – 10-Pack+ -
45W High-Output Edge-Lit LED Bar for Large Light Boxes – 958mm, 4400lm -
30W RGBW LED Light Bars – 400mm, 10-Pack+ -
8W Corner LED Module, Compact Edge-Lit Light Source for SEG Fabric Light Boxes – 202mm, 10-Pack+ -
DC Plug LED Backlight Bar for Light Boxes – 3W/6W/9W Modular System -
Edge-Lit LED Module for Light Boxes – 3.5W/7W/21W, ETL Listed, DC24V -
10W Edge-Lit LED Light Box Bars – 360mm, 10-Pack+ -
12W Dual-Angle LED Lightbox Bar – 517mm, 24V, 15°×45° Optical Lens
SHOP! Le Salon covers point-of-sale displays, furniture, lighting and LEDs. Plan how an installer can reach internal lightbox components within the retail fixture. Browse the full LED Modules range below.
Prove access with the fixture assembled
Mark the removable graphic or service panel and the power-isolation point. Trial the intended tool, screw access and module-removal route without moving shelves or damaging furniture. Keep connector access and cable clearance visible in the approved section drawing; a short bar alone does not prove serviceability.
Place the cable exit within the service opening
The profile family has a 40.7mm-wide, 17mm-high housing. Its standard 32cm lead exits at the left end on the bottom side; confirm another exit before ordering. Trial the chosen module and mating cable in the fixture. Accessible DC sockets still need a verified plug, pinout and polarity.
Compare LED lightbox sources
- 7W mini edge-lit bar: 200×23×16mm, DC24V, 770lm and standard 20°×60° optics; verify available mounting and removal space.
- 10W DC-plug edge-lit bar: 360×26×16mm including lens, DC24V, 1000lm ±10%, 15°×45° optics and dual-end DC sockets.
- Aluminum-profile edge-lit family: 22W/25W/32W, DC24V, 40.7×17mm housing and 14°×47° optics; specify length and wire exit.
Can a removable graphic replace a service-access check?
No. Confirm that the module, fasteners and cable can actually be reached and removed through that opening. Save the approved route and model before repeat fabrication.
Before ordering
These are internal light sources, not complete retail fixtures. Disconnect power before service. Verify DC24V, load, connector pinout and polarity; confirm power and hardware separately. The featured 10W DC-plug bar permits at most 6 per run after wiring checks. Do not transfer the limit to other models.
Send the fixture section, service-opening dimensions, removal-route photos, cable-exit requirement and quantity through our contact page for a component-access review.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.