RemaDays Warsaw includes illuminated advertising and point-of-sale equipment within its advertising and print scope. Compare internal LED components for lightbox fabrication and prepare traceable assembly kits. Browse all LED Modules below.
Build a parts list for each frame configuration
Label each kit with the exact LED model, frame size, required bar quantity, mounting parts and matching connector family. Count included accessories separately from components you must source. Keep spare bars labelled outside the assembly kit so surplus is not mistaken for the approved layout.
Check substitutions before the kit reaches assembly
A similar length or connector appearance does not establish interchangeability. Recheck optical direction, cable exit, pin assignment, load and mounting clearance for any substitution. Confirm the completed prototype before releasing its parts list for repeat production.
Compare LED lightbox sources
- 7W mini edge-lit bar: 200×23×16mm, DC24V, 770lm and standard 20°×60° optics; verify available mounting and removal space.
- 10W DC-plug edge-lit bar: 360×26×16mm including lens, DC24V, 1000lm ±10%, 15°×45° optics and dual-end DC sockets.
- Aluminum-profile edge-lit family: 22W/25W/32W, DC24V, 40.7×17mm housing and 14°×47° optics; specify length and wire exit.
Can different LED bar models share the same assembly-kit label?
Use separate model identification and an approved parts list. Keep the wiring limit with its exact model; changing a bar or connector requires a fresh compatibility check.
Before ordering
These are internal light sources, not complete retail fixtures. Disconnect power before service. Verify DC24V, load, connector pinout and polarity; confirm power and hardware separately. The featured 10W DC-plug bar permits at most 6 per run after wiring checks. Do not transfer the limit to other models.
Send the frame section, approved layout, LED model, connector details, parts list and production quantity through our contact page for component selection.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
-
7W 200mm Mini LED Light Box Bar – 770lm, DC24V -
10W DC Plug LED Lightbox Bar – 360mm, 24V, 15°×45° Optical Lens -
22W–32W Aluminum Profile LED Lightbox Modules – 10-Pack+ -
10W Slim Edge-Lit LED Lightbox Bar – 360mm, 9°×50° Lens -
20W Rigid LED Light Box Bars – 2200lm, DC24V, 10-Pack+ -
Flexible LED Stone Backlight Panel – 480×240mm, 24W/48W -
FOGA SYSTEM 10W LED Module – Edge-Lit Lightbox Bar -
12W Dual-CCT Switchable LED Lightbox Bar – 24V -
13W Edge-Lit LED Lightbox Bar – 360mm, 1430lm, ETL Listed -
7W DC24V Side-Lit LED Lightbox Module – Optical Lens -
Side-Lit LED Module for MODULAP Systems -
12W/18W LED Module for MODULAP Fabric Lightbox -
24W RGB Edge-Lit LED Bar for SEG Light Boxes & Displays -
32W 4-in-1 RGBW Edge-Lit LED Light Box Bars – 10-Pack+ -
14W 313mm-Long Edge-Lit LED Light Box Bars – 1540lm -
DC24V Linkable Edge-Lit LED Light Box Bars for SEG Displays -
27.5W Optical Edge-Lit LED Light Box Bars – 10-Pack+ -
45W High-Output Edge-Lit LED Bar for Large Light Boxes – 958mm, 4400lm -
30W RGBW LED Light Bars – 400mm, 10-Pack+ -
8W Corner LED Module, Compact Edge-Lit Light Source for SEG Fabric Light Boxes – 202mm, 10-Pack+ -
DC Plug LED Backlight Bar for Light Boxes – 3W/6W/9W Modular System -
Edge-Lit LED Module for Light Boxes – 3.5W/7W/21W, ETL Listed, DC24V -
10W Edge-Lit LED Light Box Bars – 360mm, 10-Pack+ -
12W Dual-Angle LED Lightbox Bar – 517mm, 24V, 15°×45° Optical Lens
RemaDays Warsaw includes illuminated advertising and point-of-sale equipment within its advertising and print scope. Compare internal LED components for lightbox fabrication and prepare traceable assembly kits. Browse all LED Modules below.
Build a parts list for each frame configuration
Label each kit with the exact LED model, frame size, required bar quantity, mounting parts and matching connector family. Count included accessories separately from components you must source. Keep spare bars labelled outside the assembly kit so surplus is not mistaken for the approved layout.
Check substitutions before the kit reaches assembly
A similar length or connector appearance does not establish interchangeability. Recheck optical direction, cable exit, pin assignment, load and mounting clearance for any substitution. Confirm the completed prototype before releasing its parts list for repeat production.
Compare LED lightbox sources
- 7W mini edge-lit bar: 200×23×16mm, DC24V, 770lm and standard 20°×60° optics; verify available mounting and removal space.
- 10W DC-plug edge-lit bar: 360×26×16mm including lens, DC24V, 1000lm ±10%, 15°×45° optics and dual-end DC sockets.
- Aluminum-profile edge-lit family: 22W/25W/32W, DC24V, 40.7×17mm housing and 14°×47° optics; specify length and wire exit.
Can different LED bar models share the same assembly-kit label?
Use separate model identification and an approved parts list. Keep the wiring limit with its exact model; changing a bar or connector requires a fresh compatibility check.
Before ordering
These are internal light sources, not complete retail fixtures. Disconnect power before service. Verify DC24V, load, connector pinout and polarity; confirm power and hardware separately. The featured 10W DC-plug bar permits at most 6 per run after wiring checks. Do not transfer the limit to other models.
Send the frame section, approved layout, LED model, connector details, parts list and production quantity through our contact page for component selection.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.