Refitting a reusable lightbox wall for a WWETT Show equipment booth? Choose internal LED bars for the retained frame, printed graphic and revised power arrangement. These components do not replace complete booth or equipment-demonstration lights.
Can I keep my existing lightbox frame when replacing the LEDs?
Survey internal depth, mounting points, supports and graphic position. Test a retained-wall section with replacement lights and the intended print: physical fit does not establish uniform illumination. Confirm the frame owner permits the mounting method.
Can I reuse the old power supply and plug-in cables?
Read driver and LED labels, not just plug shapes. For the featured DC24V bars, verify constant-voltage output, total load, cable rating, polarity and pinout before retaining any supply or cable. Mark accessible disconnection points on the revised drawing; keep storage shelves clear of service access.
Compare LED lightbox sources
- Linkable edge-lit bars: DC24V, 212mm/9W, 319mm/14W or 480mm/20W. Select length against the retained cavity and tested layout.
- 20W rigid edge-lit bar: DC24V, 470×24×16mm including lens, 2200lm ±10%, 10°×40° optics.
- 10W slim edge-lit bar: DC24V, 360×23×16mm including lens, 1100lm, 9°×50° optics.
Are lightbox LED modules the same as counter accent lighting?
No. Printed-graphic backlighting and counter decoration need separate optical and mounting decisions. Specify each circuit separately. A wastewater exhibition does not establish suitability for wet demonstrations; follow the selected model's installation conditions.
Before ordering
External power supplies are separate. The featured linkable family permits up to five compatible bars per run; the featured slim 10W model permits up to six after wiring checks. These are different model limits, not collection-wide rules. Check connected load and voltage drop.
Send retained-frame drawings, usable depth, print samples, old LED/driver labels, connector details and a circuit map. Request a sample retrofit review before ordering quantities; compare the full Modules range below.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
-
DC24V Linkable Edge-Lit LED Light Box Bars for SEG Displays -
20W Rigid LED Light Box Bars – 2200lm, DC24V, 10-Pack+ -
10W Slim Edge-Lit LED Lightbox Bar – 360mm, 9°×50° Lens -
12W/18W LED Module for MODULAP Fabric Lightbox -
45W High-Output Edge-Lit LED Bar for Large Light Boxes – 958mm, 4400lm -
12W Compact LED Lightbox Bar – 313mm, 24V, 6 LEDs, 1200lm -
18W LED Lightbox Bar – 585mm, 24V, 9 LEDs, 14°×50° Optical Lens -
10W DC Plug LED Lightbox Bar – 360mm, 24V, 15°×45° Optical Lens -
12W Dual-Angle LED Lightbox Bar – 517mm, 24V, 15°×45° Optical Lens -
22W–32W Aluminum Profile LED Lightbox Modules – 10-Pack+ -
10W Edge-Lit LED Light Box Bars – 360mm, 10-Pack+ -
Edge-Lit LED Module for Light Boxes – 3.5W/7W/21W, ETL Listed, DC24V -
DC Plug LED Backlight Bar for Light Boxes – 3W/6W/9W Modular System -
8W Corner LED Module, Compact Edge-Lit Light Source for SEG Fabric Light Boxes – 202mm, 10-Pack+ -
30W RGBW LED Light Bars – 400mm, 10-Pack+ -
27.5W Optical Edge-Lit LED Light Box Bars – 10-Pack+ -
14W 313mm-Long Edge-Lit LED Light Box Bars – 1540lm -
32W 4-in-1 RGBW Edge-Lit LED Light Box Bars – 10-Pack+ -
24W RGB Edge-Lit LED Bar for SEG Light Boxes & Displays -
Side-Lit LED Module for MODULAP Systems -
7W DC24V Side-Lit LED Lightbox Module – Optical Lens -
7W 200mm Mini LED Light Box Bar – 770lm, DC24V -
13W Edge-Lit LED Lightbox Bar – 360mm, 1430lm, ETL Listed -
12W Dual-CCT Switchable LED Lightbox Bar – 24V
Refitting a reusable lightbox wall for a WWETT Show equipment booth? Choose internal LED bars for the retained frame, printed graphic and revised power arrangement. These components do not replace complete booth or equipment-demonstration lights.
Can I keep my existing lightbox frame when replacing the LEDs?
Survey internal depth, mounting points, supports and graphic position. Test a retained-wall section with replacement lights and the intended print: physical fit does not establish uniform illumination. Confirm the frame owner permits the mounting method.
Can I reuse the old power supply and plug-in cables?
Read driver and LED labels, not just plug shapes. For the featured DC24V bars, verify constant-voltage output, total load, cable rating, polarity and pinout before retaining any supply or cable. Mark accessible disconnection points on the revised drawing; keep storage shelves clear of service access.
Compare LED lightbox sources
- Linkable edge-lit bars: DC24V, 212mm/9W, 319mm/14W or 480mm/20W. Select length against the retained cavity and tested layout.
- 20W rigid edge-lit bar: DC24V, 470×24×16mm including lens, 2200lm ±10%, 10°×40° optics.
- 10W slim edge-lit bar: DC24V, 360×23×16mm including lens, 1100lm, 9°×50° optics.
Are lightbox LED modules the same as counter accent lighting?
No. Printed-graphic backlighting and counter decoration need separate optical and mounting decisions. Specify each circuit separately. A wastewater exhibition does not establish suitability for wet demonstrations; follow the selected model's installation conditions.
Before ordering
External power supplies are separate. The featured linkable family permits up to five compatible bars per run; the featured slim 10W model permits up to six after wiring checks. These are different model limits, not collection-wide rules. Check connected load and voltage drop.
Send retained-frame drawings, usable depth, print samples, old LED/driver labels, connector details and a circuit map. Request a sample retrofit review before ordering quantities; compare the full Modules range below.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.