Looking for Vancouver Auto Show fabric lightbox LED modules? A builder documents fabric lightbox towers at the Vancouver International Auto Show. Compare internal sources for your own independently specified display, including its wiring and access arrangements.
How do I route LED wiring without casting shadows on the fabric?
Plan cable paths outside the intended light path and allow access to connections. Test the actual printed face with wiring and frame members in place, rather than approving the light sources alone. Confirm that routing leaves the required mounting clearance.
Can I replace the connector or extend the cable on any LED bar?
Do not assume connectors are interchangeable. Check the selected product’s voltage, polarity, connector pinout, wiring requirements and permitted connections. Have the proposed extension assessed for electrical suitability before changing the circuit; never use appearance alone to choose a connector.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Does an accessible cable route prove that the complete tower is suitable?
No. Electrical access does not establish frame fit, structural stability or venue approval. Check the complete build with the responsible supplier. These modules are internal light sources; no approved replacement for a proprietary exhibit system is claimed.
Before ordering
For the three featured bars: Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Browse all LED Modules below. Send frame sections, source positions, connector photos, planned cable paths and supply details through Contact us to compare components.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
-
20W Rigid LED Light Box Bars – 2200lm, DC24V, 10-Pack+ -
12W Dual-CCT Switchable LED Lightbox Bar – 24V -
10W Slim Edge-Lit LED Lightbox Bar – 360mm, 9°×50° Lens -
12W/18W LED Module for MODULAP Fabric Lightbox -
45W High-Output Edge-Lit LED Bar for Large Light Boxes – 958mm, 4400lm -
DC24V Linkable Edge-Lit LED Light Box Bars for SEG Displays -
12W Compact LED Lightbox Bar – 313mm, 24V, 6 LEDs, 1200lm -
18W LED Lightbox Bar – 585mm, 24V, 9 LEDs, 14°×50° Optical Lens -
10W DC Plug LED Lightbox Bar – 360mm, 24V, 15°×45° Optical Lens -
12W Dual-Angle LED Lightbox Bar – 517mm, 24V, 15°×45° Optical Lens -
22W–32W Aluminum Profile LED Lightbox Modules – 10-Pack+ -
10W Edge-Lit LED Light Box Bars – 360mm, 10-Pack+ -
Edge-Lit LED Module for Light Boxes – 3.5W/7W/21W, ETL Listed, DC24V -
DC Plug LED Backlight Bar for Light Boxes – 3W/6W/9W Modular System -
8W Corner LED Module, Compact Edge-Lit Light Source for SEG Fabric Light Boxes – 202mm, 10-Pack+ -
30W RGBW LED Light Bars – 400mm, 10-Pack+ -
27.5W Optical Edge-Lit LED Light Box Bars – 10-Pack+ -
14W 313mm-Long Edge-Lit LED Light Box Bars – 1540lm -
32W 4-in-1 RGBW Edge-Lit LED Light Box Bars – 10-Pack+ -
24W RGB Edge-Lit LED Bar for SEG Light Boxes & Displays -
Side-Lit LED Module for MODULAP Systems -
7W DC24V Side-Lit LED Lightbox Module – Optical Lens -
7W 200mm Mini LED Light Box Bar – 770lm, DC24V -
13W Edge-Lit LED Lightbox Bar – 360mm, 1430lm, ETL Listed
Looking for Vancouver Auto Show fabric lightbox LED modules? A builder documents fabric lightbox towers at the Vancouver International Auto Show. Compare internal sources for your own independently specified display, including its wiring and access arrangements.
How do I route LED wiring without casting shadows on the fabric?
Plan cable paths outside the intended light path and allow access to connections. Test the actual printed face with wiring and frame members in place, rather than approving the light sources alone. Confirm that routing leaves the required mounting clearance.
Can I replace the connector or extend the cable on any LED bar?
Do not assume connectors are interchangeable. Check the selected product’s voltage, polarity, connector pinout, wiring requirements and permitted connections. Have the proposed extension assessed for electrical suitability before changing the circuit; never use appearance alone to choose a connector.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Does an accessible cable route prove that the complete tower is suitable?
No. Electrical access does not establish frame fit, structural stability or venue approval. Check the complete build with the responsible supplier. These modules are internal light sources; no approved replacement for a proprietary exhibit system is claimed.
Before ordering
For the three featured bars: Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Browse all LED Modules below. Send frame sections, source positions, connector photos, planned cable paths and supply details through Contact us to compare components.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.