Trotec Black Line Open House presents laser-production workflows for sign, display and print businesses. Its signage application guidance includes illuminated advertising. For indoor lightbox builders, this collection focuses on handing over the released cut-file revision with the LED assembly record.
Tie the physical face to the released cut file
Give the cut file a revision reference and label the matching face or retained sample. Record the material reference and final cut outline beside the lighting trial. A drawing thumbnail cannot establish which face was actually tested; preserve the file reference and the assembly result together.
Review changed contours before repeating an LED layout
If a cut outline, aperture or fixing position changes, flag the change during the handoff from fabrication to assembly. Check the representative finished face with the proposed LED layout and available clearance. Keep the previous result separately; obtain a fresh assembly approval before repeating production.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Does an unchanged LED bar make a revised cut face equivalent?
No. Changed geometry can alter the light path or usable installation space. Review the complete assembly. This is independent component-selection guidance, not a claim that BOOTH LIGHTS products are demonstrated by Trotec or approved for its machines.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Compare all LED Modules below. Send the lightbox depth, released drawing reference, changed contour details and intended power arrangement to discuss candidates before purchase.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
-
20W Rigid LED Light Box Bars – 2200lm, DC24V, 10-Pack+ -
12W Dual-CCT Switchable LED Lightbox Bar – 24V -
10W Slim Edge-Lit LED Lightbox Bar – 360mm, 9°×50° Lens -
12W/18W LED Module for MODULAP Fabric Lightbox -
45W High-Output Edge-Lit LED Bar for Large Light Boxes – 958mm, 4400lm -
DC24V Linkable Edge-Lit LED Light Box Bars for SEG Displays -
12W Compact LED Lightbox Bar – 313mm, 24V, 6 LEDs, 1200lm -
18W LED Lightbox Bar – 585mm, 24V, 9 LEDs, 14°×50° Optical Lens -
10W DC Plug LED Lightbox Bar – 360mm, 24V, 15°×45° Optical Lens -
12W Dual-Angle LED Lightbox Bar – 517mm, 24V, 15°×45° Optical Lens -
22W–32W Aluminum Profile LED Lightbox Modules – 10-Pack+ -
10W Edge-Lit LED Light Box Bars – 360mm, 10-Pack+ -
Edge-Lit LED Module for Light Boxes – 3.5W/7W/21W, ETL Listed, DC24V -
DC Plug LED Backlight Bar for Light Boxes – 3W/6W/9W Modular System -
8W Corner LED Module, Compact Edge-Lit Light Source for SEG Fabric Light Boxes – 202mm, 10-Pack+ -
30W RGBW LED Light Bars – 400mm, 10-Pack+ -
27.5W Optical Edge-Lit LED Light Box Bars – 10-Pack+ -
14W 313mm-Long Edge-Lit LED Light Box Bars – 1540lm -
32W 4-in-1 RGBW Edge-Lit LED Light Box Bars – 10-Pack+ -
24W RGB Edge-Lit LED Bar for SEG Light Boxes & Displays -
Side-Lit LED Module for MODULAP Systems -
7W DC24V Side-Lit LED Lightbox Module – Optical Lens -
7W 200mm Mini LED Light Box Bar – 770lm, DC24V -
13W Edge-Lit LED Lightbox Bar – 360mm, 1430lm, ETL Listed
Trotec Black Line Open House presents laser-production workflows for sign, display and print businesses. Its signage application guidance includes illuminated advertising. For indoor lightbox builders, this collection focuses on handing over the released cut-file revision with the LED assembly record.
Tie the physical face to the released cut file
Give the cut file a revision reference and label the matching face or retained sample. Record the material reference and final cut outline beside the lighting trial. A drawing thumbnail cannot establish which face was actually tested; preserve the file reference and the assembly result together.
Review changed contours before repeating an LED layout
If a cut outline, aperture or fixing position changes, flag the change during the handoff from fabrication to assembly. Check the representative finished face with the proposed LED layout and available clearance. Keep the previous result separately; obtain a fresh assembly approval before repeating production.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Does an unchanged LED bar make a revised cut face equivalent?
No. Changed geometry can alter the light path or usable installation space. Review the complete assembly. This is independent component-selection guidance, not a claim that BOOTH LIGHTS products are demonstrated by Trotec or approved for its machines.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Compare all LED Modules below. Send the lightbox depth, released drawing reference, changed contour details and intended power arrangement to discuss candidates before purchase.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.