Specifying an independently designed backlit SEG tower for an RE+ clean-energy stand? Compare all 26 LED Modules products for its internal light source. Include the surrounding demonstration equipment when reviewing the enclosure's operating conditions.
Review the closed tower in its actual stand layout
Use the intended fabric, internal LED layout and external driver in the trial assembly. Identify nearby equipment that releases heat and record its position and operating state. Keep component measurements tied to that configuration; a test with the fabric removed or neighbouring equipment switched off represents a different condition.
Use component limits to decide the next trial
Request the applicable operating-temperature limits and installation guidance for the chosen LEDs, driver and other enclosure components. Have the builder assess measured conditions against those documents rather than inventing a universal safe temperature. If source density, driver location, enclosure ventilation or neighbouring equipment changes, repeat the assessment before approving a production order.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Can these LED modules run directly from displayed solar or storage equipment?
Do not assume that. They are lightbox components requiring the specified voltage, polarity and suitable power supply. The stand's PV, inverter or battery demonstration does not establish a compatible connection or approval.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the tower section, fabric specification, LED and driver layout, nearby equipment positions and available supply details for an LED module comparison.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
-
20W Rigid LED Light Box Bars – 2200lm, DC24V, 10-Pack+ -
12W Dual-CCT Switchable LED Lightbox Bar – 24V -
10W Slim Edge-Lit LED Lightbox Bar – 360mm, 9°×50° Lens -
12W/18W LED Module for MODULAP Fabric Lightbox -
45W High-Output Edge-Lit LED Bar for Large Light Boxes – 958mm, 4400lm -
DC24V Linkable Edge-Lit LED Light Box Bars for SEG Displays -
12W Compact LED Lightbox Bar – 313mm, 24V, 6 LEDs, 1200lm -
18W LED Lightbox Bar – 585mm, 24V, 9 LEDs, 14°×50° Optical Lens -
10W DC Plug LED Lightbox Bar – 360mm, 24V, 15°×45° Optical Lens -
12W Dual-Angle LED Lightbox Bar – 517mm, 24V, 15°×45° Optical Lens -
22W–32W Aluminum Profile LED Lightbox Modules – 10-Pack+ -
10W Edge-Lit LED Light Box Bars – 360mm, 10-Pack+ -
Edge-Lit LED Module for Light Boxes – 3.5W/7W/21W, ETL Listed, DC24V -
DC Plug LED Backlight Bar for Light Boxes – 3W/6W/9W Modular System -
8W Corner LED Module, Compact Edge-Lit Light Source for SEG Fabric Light Boxes – 202mm, 10-Pack+ -
30W RGBW LED Light Bars – 400mm, 10-Pack+ -
27.5W Optical Edge-Lit LED Light Box Bars – 10-Pack+ -
14W 313mm-Long Edge-Lit LED Light Box Bars – 1540lm -
32W 4-in-1 RGBW Edge-Lit LED Light Box Bars – 10-Pack+ -
24W RGB Edge-Lit LED Bar for SEG Light Boxes & Displays -
Side-Lit LED Module for MODULAP Systems -
7W DC24V Side-Lit LED Lightbox Module – Optical Lens -
7W 200mm Mini LED Light Box Bar – 770lm, DC24V -
13W Edge-Lit LED Lightbox Bar – 360mm, 1430lm, ETL Listed
Specifying an independently designed backlit SEG tower for an RE+ clean-energy stand? Compare all 26 LED Modules products for its internal light source. Include the surrounding demonstration equipment when reviewing the enclosure's operating conditions.
Review the closed tower in its actual stand layout
Use the intended fabric, internal LED layout and external driver in the trial assembly. Identify nearby equipment that releases heat and record its position and operating state. Keep component measurements tied to that configuration; a test with the fabric removed or neighbouring equipment switched off represents a different condition.
Use component limits to decide the next trial
Request the applicable operating-temperature limits and installation guidance for the chosen LEDs, driver and other enclosure components. Have the builder assess measured conditions against those documents rather than inventing a universal safe temperature. If source density, driver location, enclosure ventilation or neighbouring equipment changes, repeat the assessment before approving a production order.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Can these LED modules run directly from displayed solar or storage equipment?
Do not assume that. They are lightbox components requiring the specified voltage, polarity and suitable power supply. The stand's PV, inverter or battery demonstration does not establish a compatible connection or approval.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the tower section, fabric specification, LED and driver layout, nearby equipment positions and available supply details for an LED module comparison.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.