Comparing signmaking materials after a Grimco Open House? Explore all 26 LED Modules products for independently built indoor graphic lightboxes. Keep the printed face and internal light source together in the sample review.
Bring a matched print offcut to the lightbox trial
Keep a reference offcut from the same translucent-media and print run as the intended graphic. Label its material, print orientation and any white-ink or backing treatment. An unprinted translucent sample cannot show how the finished artwork transmits light. Ask the builder to trial the printed offcut in the proposed frame with the candidate source.
Change one sample variable and retain the reference
When comparing edge-lit and rear-backlit layouts, document the frame depth, source positions, selected power supply and print treatment for each assembly. Keep the original reference available when reviewing another module or material. Check fine lettering, dark areas and the full graphic face; record which combination was reviewed rather than attributing a difference to the LED alone.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Can a good-looking loose sample prove the production lightbox will match?
No. A loose print or exposed LED is not the completed optical assembly. Review the proposed source, mounting, frame and actual print together. Do not assume our modules replace a showcased supplier system or that an open-house demonstration used BOOTH LIGHTS products.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the labelled print sample, frame cross-section, proposed source positions and electrical details for an LED module comparison.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
-
20W Rigid LED Light Box Bars – 2200lm, DC24V, 10-Pack+ -
12W Dual-CCT Switchable LED Lightbox Bar – 24V -
10W Slim Edge-Lit LED Lightbox Bar – 360mm, 9°×50° Lens -
12W/18W LED Module for MODULAP Fabric Lightbox -
45W High-Output Edge-Lit LED Bar for Large Light Boxes – 958mm, 4400lm -
DC24V Linkable Edge-Lit LED Light Box Bars for SEG Displays -
12W Compact LED Lightbox Bar – 313mm, 24V, 6 LEDs, 1200lm -
18W LED Lightbox Bar – 585mm, 24V, 9 LEDs, 14°×50° Optical Lens -
10W DC Plug LED Lightbox Bar – 360mm, 24V, 15°×45° Optical Lens -
12W Dual-Angle LED Lightbox Bar – 517mm, 24V, 15°×45° Optical Lens -
22W–32W Aluminum Profile LED Lightbox Modules – 10-Pack+ -
10W Edge-Lit LED Light Box Bars – 360mm, 10-Pack+ -
Edge-Lit LED Module for Light Boxes – 3.5W/7W/21W, ETL Listed, DC24V -
DC Plug LED Backlight Bar for Light Boxes – 3W/6W/9W Modular System -
8W Corner LED Module, Compact Edge-Lit Light Source for SEG Fabric Light Boxes – 202mm, 10-Pack+ -
30W RGBW LED Light Bars – 400mm, 10-Pack+ -
27.5W Optical Edge-Lit LED Light Box Bars – 10-Pack+ -
14W 313mm-Long Edge-Lit LED Light Box Bars – 1540lm -
32W 4-in-1 RGBW Edge-Lit LED Light Box Bars – 10-Pack+ -
24W RGB Edge-Lit LED Bar for SEG Light Boxes & Displays -
Side-Lit LED Module for MODULAP Systems -
7W DC24V Side-Lit LED Lightbox Module – Optical Lens -
7W 200mm Mini LED Light Box Bar – 770lm, DC24V -
13W Edge-Lit LED Lightbox Bar – 360mm, 1430lm, ETL Listed
Comparing signmaking materials after a Grimco Open House? Explore all 26 LED Modules products for independently built indoor graphic lightboxes. Keep the printed face and internal light source together in the sample review.
Bring a matched print offcut to the lightbox trial
Keep a reference offcut from the same translucent-media and print run as the intended graphic. Label its material, print orientation and any white-ink or backing treatment. An unprinted translucent sample cannot show how the finished artwork transmits light. Ask the builder to trial the printed offcut in the proposed frame with the candidate source.
Change one sample variable and retain the reference
When comparing edge-lit and rear-backlit layouts, document the frame depth, source positions, selected power supply and print treatment for each assembly. Keep the original reference available when reviewing another module or material. Check fine lettering, dark areas and the full graphic face; record which combination was reviewed rather than attributing a difference to the LED alone.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Can a good-looking loose sample prove the production lightbox will match?
No. A loose print or exposed LED is not the completed optical assembly. Review the proposed source, mounting, frame and actual print together. Do not assume our modules replace a showcased supplier system or that an open-house demonstration used BOOTH LIGHTS products.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the labelled print sample, frame cross-section, proposed source positions and electrical details for an LED module comparison.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.