Looking for DKOU lightbox LED modules for separate graphic walls? Compare internal LED bars for each actual illuminated section, including low walls beside information and discussion areas.
Which LED bars suit a low graphic lightbox wall?
Use the clear internal depth, lit opening, final graphic material and mounting positions to compare sources. A low wall does not automatically need a low-power or side-lit bar. Test the chosen source and front together before fixing bar spacing and quantities.
Can separate lightbox walls use one power supply?
Only after checking the selected products, combined load, wiring route and supply rating. Review voltage, cable sizing, polarity and connector pinout for each section. Keep service access available so one wall can be checked without dismantling the other; an existing plug does not prove compatibility.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Can lightbox LED modules replace overhead stand lights?
They light graphic enclosures internally. Overhead spotlights, lighting bridges and decorative elements require their own lighting design. Specify the graphic walls separately, and ask your builder to check current structural and installation requirements rather than assuming one case layout is a congress rule.
Before ordering
For the three featured bars: Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Compare all LED Modules below. Send each wall drawing, clear depth, final graphic sample and power labels to review suitable internal bars and wiring.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
-
20W Rigid LED Light Box Bars – 2200lm, DC24V, 10-Pack+ -
12W Dual-CCT Switchable LED Lightbox Bar – 24V -
10W Slim Edge-Lit LED Lightbox Bar – 360mm, 9°×50° Lens -
12W/18W LED Module for MODULAP Fabric Lightbox -
45W High-Output Edge-Lit LED Bar for Large Light Boxes – 958mm, 4400lm -
DC24V Linkable Edge-Lit LED Light Box Bars for SEG Displays -
12W Compact LED Lightbox Bar – 313mm, 24V, 6 LEDs, 1200lm -
18W LED Lightbox Bar – 585mm, 24V, 9 LEDs, 14°×50° Optical Lens -
10W DC Plug LED Lightbox Bar – 360mm, 24V, 15°×45° Optical Lens -
12W Dual-Angle LED Lightbox Bar – 517mm, 24V, 15°×45° Optical Lens -
22W–32W Aluminum Profile LED Lightbox Modules – 10-Pack+ -
10W Edge-Lit LED Light Box Bars – 360mm, 10-Pack+ -
Edge-Lit LED Module for Light Boxes – 3.5W/7W/21W, ETL Listed, DC24V -
DC Plug LED Backlight Bar for Light Boxes – 3W/6W/9W Modular System -
8W Corner LED Module, Compact Edge-Lit Light Source for SEG Fabric Light Boxes – 202mm, 10-Pack+ -
30W RGBW LED Light Bars – 400mm, 10-Pack+ -
27.5W Optical Edge-Lit LED Light Box Bars – 10-Pack+ -
14W 313mm-Long Edge-Lit LED Light Box Bars – 1540lm -
32W 4-in-1 RGBW Edge-Lit LED Light Box Bars – 10-Pack+ -
24W RGB Edge-Lit LED Bar for SEG Light Boxes & Displays -
Side-Lit LED Module for MODULAP Systems -
7W DC24V Side-Lit LED Lightbox Module – Optical Lens -
7W 200mm Mini LED Light Box Bar – 770lm, DC24V -
13W Edge-Lit LED Lightbox Bar – 360mm, 1430lm, ETL Listed
Looking for DKOU lightbox LED modules for separate graphic walls? Compare internal LED bars for each actual illuminated section, including low walls beside information and discussion areas.
Which LED bars suit a low graphic lightbox wall?
Use the clear internal depth, lit opening, final graphic material and mounting positions to compare sources. A low wall does not automatically need a low-power or side-lit bar. Test the chosen source and front together before fixing bar spacing and quantities.
Can separate lightbox walls use one power supply?
Only after checking the selected products, combined load, wiring route and supply rating. Review voltage, cable sizing, polarity and connector pinout for each section. Keep service access available so one wall can be checked without dismantling the other; an existing plug does not prove compatibility.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Can lightbox LED modules replace overhead stand lights?
They light graphic enclosures internally. Overhead spotlights, lighting bridges and decorative elements require their own lighting design. Specify the graphic walls separately, and ask your builder to check current structural and installation requirements rather than assuming one case layout is a congress rule.
Before ordering
For the three featured bars: Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Compare all LED Modules below. Send each wall drawing, clear depth, final graphic sample and power labels to review suitable internal bars and wiring.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.