Preparing a printed backlit counter for an independent ASCO Annual Meeting exhibit? This selection focuses on the internal light source where a lockable counter also needs workable access to its lighting components. Compare all 26 LED Modules products against your own counter drawing and sample.
Check the door and latch movement before fixing the LED positions
Show the door's opening arc, hinge, latch and locking mechanism on the counter section alongside the proposed module fasteners and connector. Check the cable route through the full door movement, including the closed and latched position. A bar that fits behind the graphic with the door open may obstruct the latch or leave a cable trapped when the counter closes. Plan access to the external supply without treating a locking storage compartment as an approved place for every electrical component.
Test illumination with the finished counter closed
Fit the actual printed face and intended backing, then close and latch the counter before evaluating the proposed LED layout. Record whether an internal shelf, latch plate or cable creates a shadow on the graphic. Repeat the access and closure check after changing a source, fastener or wiring position, and retain the accepted closed-counter configuration with the component list. Review a removable graphic panel separately from the storage door; opening one does not establish that the other provides a practical lighting service route.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Does selecting an LED module establish the safety or compatibility of a locking counter?
No. The module is an internal light source, not a lock, counter structure or proprietary-frame replacement approval. Check the actual counter's mounting and electrical requirements independently. An ASCO exhibit application does not qualify these components for clinical, examination or medical-device lighting.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the counter section, door and latch drawing, cable route and printed-face sample to discuss a suitable LED component trial.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
-
20W Rigid LED Light Box Bars – 2200lm, DC24V, 10-Pack+ -
12W Dual-CCT Switchable LED Lightbox Bar – 24V -
10W Slim Edge-Lit LED Lightbox Bar – 360mm, 9°×50° Lens -
12W/18W LED Module for MODULAP Fabric Lightbox -
45W High-Output Edge-Lit LED Bar for Large Light Boxes – 958mm, 4400lm -
DC24V Linkable Edge-Lit LED Light Box Bars for SEG Displays -
12W Compact LED Lightbox Bar – 313mm, 24V, 6 LEDs, 1200lm -
18W LED Lightbox Bar – 585mm, 24V, 9 LEDs, 14°×50° Optical Lens -
10W DC Plug LED Lightbox Bar – 360mm, 24V, 15°×45° Optical Lens -
12W Dual-Angle LED Lightbox Bar – 517mm, 24V, 15°×45° Optical Lens -
22W–32W Aluminum Profile LED Lightbox Modules – 10-Pack+ -
10W Edge-Lit LED Light Box Bars – 360mm, 10-Pack+ -
Edge-Lit LED Module for Light Boxes – 3.5W/7W/21W, ETL Listed, DC24V -
DC Plug LED Backlight Bar for Light Boxes – 3W/6W/9W Modular System -
8W Corner LED Module, Compact Edge-Lit Light Source for SEG Fabric Light Boxes – 202mm, 10-Pack+ -
30W RGBW LED Light Bars – 400mm, 10-Pack+ -
27.5W Optical Edge-Lit LED Light Box Bars – 10-Pack+ -
14W 313mm-Long Edge-Lit LED Light Box Bars – 1540lm -
32W 4-in-1 RGBW Edge-Lit LED Light Box Bars – 10-Pack+ -
24W RGB Edge-Lit LED Bar for SEG Light Boxes & Displays -
Side-Lit LED Module for MODULAP Systems -
7W DC24V Side-Lit LED Lightbox Module – Optical Lens -
7W 200mm Mini LED Light Box Bar – 770lm, DC24V -
13W Edge-Lit LED Lightbox Bar – 360mm, 1430lm, ETL Listed
Preparing a printed backlit counter for an independent ASCO Annual Meeting exhibit? This selection focuses on the internal light source where a lockable counter also needs workable access to its lighting components. Compare all 26 LED Modules products against your own counter drawing and sample.
Check the door and latch movement before fixing the LED positions
Show the door's opening arc, hinge, latch and locking mechanism on the counter section alongside the proposed module fasteners and connector. Check the cable route through the full door movement, including the closed and latched position. A bar that fits behind the graphic with the door open may obstruct the latch or leave a cable trapped when the counter closes. Plan access to the external supply without treating a locking storage compartment as an approved place for every electrical component.
Test illumination with the finished counter closed
Fit the actual printed face and intended backing, then close and latch the counter before evaluating the proposed LED layout. Record whether an internal shelf, latch plate or cable creates a shadow on the graphic. Repeat the access and closure check after changing a source, fastener or wiring position, and retain the accepted closed-counter configuration with the component list. Review a removable graphic panel separately from the storage door; opening one does not establish that the other provides a practical lighting service route.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Does selecting an LED module establish the safety or compatibility of a locking counter?
No. The module is an internal light source, not a lock, counter structure or proprietary-frame replacement approval. Check the actual counter's mounting and electrical requirements independently. An ASCO exhibit application does not qualify these components for clinical, examination or medical-device lighting.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the counter section, door and latch drawing, cable route and printed-face sample to discuss a suitable LED component trial.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.