Aluvision Academy offers structured modular-system training and hands-on learning. For teams developing their own indoor lightboxes, compare all LED Modules below and prepare assembly information that another team member can follow.
Document the component installation
Show the frame section, LED mounting points, bar orientation and cable route. Name the selected model and connector, and distinguish supplied parts from separate power and controls. Keep the drawing and parts record together so an assembler can identify the intended configuration rather than infer it from a finished display photo.
Use the evaluated build for the team handoff
Assemble a complete sample with the actual graphic. Record illumination observations, connector access and the order in which removable parts are fitted. Include photos of the internal arrangement before closing the frame. If the production team changes a component or mounting position, review that change rather than treating the original sample approval as universal.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Does Academy training certify these modules for Aluvision systems?
No. This collection supports independent component enquiries, not supplier certification or authorized replacement status. No universal Aluvision compatibility is claimed. Confirm the exact mechanical and electrical arrangement before proposing parts for an existing proprietary display.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the assembly drawing, parts record, candidate models, internal photos and sample observations through our contact page.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
-
20W Rigid LED Light Box Bars – 2200lm, DC24V, 10-Pack+ -
12W Dual-CCT Switchable LED Lightbox Bar – 24V -
10W Slim Edge-Lit LED Lightbox Bar – 360mm, 9°×50° Lens -
12W/18W LED Module for MODULAP Fabric Lightbox -
45W High-Output Edge-Lit LED Bar for Large Light Boxes – 958mm, 4400lm -
DC24V Linkable Edge-Lit LED Light Box Bars for SEG Displays -
12W Compact LED Lightbox Bar – 313mm, 24V, 6 LEDs, 1200lm -
18W LED Lightbox Bar – 585mm, 24V, 9 LEDs, 14°×50° Optical Lens -
10W DC Plug LED Lightbox Bar – 360mm, 24V, 15°×45° Optical Lens -
12W Dual-Angle LED Lightbox Bar – 517mm, 24V, 15°×45° Optical Lens -
22W–32W Aluminum Profile LED Lightbox Modules – 10-Pack+ -
10W Edge-Lit LED Light Box Bars – 360mm, 10-Pack+ -
Edge-Lit LED Module for Light Boxes – 3.5W/7W/21W, ETL Listed, DC24V -
DC Plug LED Backlight Bar for Light Boxes – 3W/6W/9W Modular System -
8W Corner LED Module, Compact Edge-Lit Light Source for SEG Fabric Light Boxes – 202mm, 10-Pack+ -
30W RGBW LED Light Bars – 400mm, 10-Pack+ -
27.5W Optical Edge-Lit LED Light Box Bars – 10-Pack+ -
14W 313mm-Long Edge-Lit LED Light Box Bars – 1540lm -
32W 4-in-1 RGBW Edge-Lit LED Light Box Bars – 10-Pack+ -
24W RGB Edge-Lit LED Bar for SEG Light Boxes & Displays -
Side-Lit LED Module for MODULAP Systems -
7W DC24V Side-Lit LED Lightbox Module – Optical Lens -
7W 200mm Mini LED Light Box Bar – 770lm, DC24V -
13W Edge-Lit LED Lightbox Bar – 360mm, 1430lm, ETL Listed
Aluvision Academy offers structured modular-system training and hands-on learning. For teams developing their own indoor lightboxes, compare all LED Modules below and prepare assembly information that another team member can follow.
Document the component installation
Show the frame section, LED mounting points, bar orientation and cable route. Name the selected model and connector, and distinguish supplied parts from separate power and controls. Keep the drawing and parts record together so an assembler can identify the intended configuration rather than infer it from a finished display photo.
Use the evaluated build for the team handoff
Assemble a complete sample with the actual graphic. Record illumination observations, connector access and the order in which removable parts are fitted. Include photos of the internal arrangement before closing the frame. If the production team changes a component or mounting position, review that change rather than treating the original sample approval as universal.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Does Academy training certify these modules for Aluvision systems?
No. This collection supports independent component enquiries, not supplier certification or authorized replacement status. No universal Aluvision compatibility is claimed. Confirm the exact mechanical and electrical arrangement before proposing parts for an existing proprietary display.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the assembly drawing, parts record, candidate models, internal photos and sample observations through our contact page.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.