Choosing internal lightbox LEDs for a PET-film graphic after PACK PRINT INTERNATIONAL? Compare the full LED Modules range for an indoor sample frame. Start with the exact backlit film and finished print; then check how the film is retained and illuminated before ordering components.
Check film construction and flatness before increasing LED output
The organizer's show report confirms HP Latex participation, and HP's own polyester-film guide distinguishes translucent backlit PET from frontlit film that may have a light-blocking backing. This supports a lightbox selection topic, not automatic LED compatibility. Test your approved print in your own or builder-approved frame, including the retaining rail and any visible curl.
Compare LED Modules for your test frame
- DC24V linkable edge-lit bars: 212mm/9W, 319mm/14W or 480mm/20W for modular lightbox builds.
- 12W/18W DC24V MODULAP lightbox module: 470mm edge-lighting format for compatible fabric frames; verify the connector and fit.
- 20W DC24V rigid lightbox bar: 470mm, 2200lm ±10%, for tested indoor SEG and illuminated-sign layouts.
- 7W DC24V compact lightbox bar: 200mm, 770lm, 200×23×16mm body for short frame sections. Check the Molex 5557 / Mini-Fit Jr. connector family, mating pinout and fit before replacement.
Can grey-back frontlit PET replace a backlit film?
Do not substitute based on the PET name alone. A light-blocking backing can prevent the intended transmission. Verify the exact media code and backlit application with the print supplier; stronger LED bars do not establish that an opaque graphic is suitable.
How should I check film curl and retaining-edge shadows?
Install the finished print with the proposed retaining method and viewing orientation. Inspect the edges and central face at the intended distance, keeping the frame and lighting fixed. Correct mounting or print orientation before attributing a local shadow to insufficient LED power.
Which LED details belong in a PET lightbox trial quotation?
Send film code, finished size, printed-side orientation, frame section and edge-retention photos. Include bar layout, diffuser position if used, DC24V driver load, connector pinout and each model's connection limits. Test the finished face; the printer's UV-LED curing system is a different component from lightbox illumination.
Before ordering
LED Modules illuminate a printed face inside a lightbox; they are not complete signs. Confirm connector polarity, driver capacity, thermal conditions and connection limits. Check the selected bar length and product pack quantity. Do not assume outdoor or moisture suitability from a retrofit application.
Send cabinet photos, internal dimensions, frame drawings, the existing driver specification and proposed product links through our contact page to discuss a trial selection.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
Choosing internal lightbox LEDs for a PET-film graphic after PACK PRINT INTERNATIONAL? Compare the full LED Modules range for an indoor sample frame. Start with the exact backlit film and finished print; then check how the film is retained and illuminated before ordering components.
Check film construction and flatness before increasing LED output
The organizer's show report confirms HP Latex participation, and HP's own polyester-film guide distinguishes translucent backlit PET from frontlit film that may have a light-blocking backing. This supports a lightbox selection topic, not automatic LED compatibility. Test your approved print in your own or builder-approved frame, including the retaining rail and any visible curl.
Compare LED Modules for your test frame
- DC24V linkable edge-lit bars: 212mm/9W, 319mm/14W or 480mm/20W for modular lightbox builds.
- 12W/18W DC24V MODULAP lightbox module: 470mm edge-lighting format for compatible fabric frames; verify the connector and fit.
- 20W DC24V rigid lightbox bar: 470mm, 2200lm ±10%, for tested indoor SEG and illuminated-sign layouts.
- 7W DC24V compact lightbox bar: 200mm, 770lm, 200×23×16mm body for short frame sections. Check the Molex 5557 / Mini-Fit Jr. connector family, mating pinout and fit before replacement.
Can grey-back frontlit PET replace a backlit film?
Do not substitute based on the PET name alone. A light-blocking backing can prevent the intended transmission. Verify the exact media code and backlit application with the print supplier; stronger LED bars do not establish that an opaque graphic is suitable.
How should I check film curl and retaining-edge shadows?
Install the finished print with the proposed retaining method and viewing orientation. Inspect the edges and central face at the intended distance, keeping the frame and lighting fixed. Correct mounting or print orientation before attributing a local shadow to insufficient LED power.
Which LED details belong in a PET lightbox trial quotation?
Send film code, finished size, printed-side orientation, frame section and edge-retention photos. Include bar layout, diffuser position if used, DC24V driver load, connector pinout and each model's connection limits. Test the finished face; the printer's UV-LED curing system is a different component from lightbox illumination.
Before ordering
LED Modules illuminate a printed face inside a lightbox; they are not complete signs. Confirm connector polarity, driver capacity, thermal conditions and connection limits. Check the selected bar length and product pack quantity. Do not assume outdoor or moisture suitability from a retrofit application.
Send cabinet photos, internal dimensions, frame drawings, the existing driver specification and proposed product links through our contact page to discuss a trial selection.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.