Refitting a reusable lightbox wall for a WWETT Show equipment booth? Choose internal LED bars for the retained frame, printed graphic and revised power arrangement. These components do not replace complete booth or equipment-demonstration lights.
Can I keep my existing lightbox frame when replacing the LEDs?
Survey internal depth, mounting points, supports and graphic position. Test a retained-wall section with replacement lights and the intended print: physical fit does not establish uniform illumination. Confirm the frame owner permits the mounting method.
Can I reuse the old power supply and plug-in cables?
Read driver and LED labels, not just plug shapes. For the featured DC24V bars, verify constant-voltage output, total load, cable rating, polarity and pinout before retaining any supply or cable. Mark accessible disconnection points on the revised drawing; keep storage shelves clear of service access.
Compare LED lightbox sources
- Linkable edge-lit bars: DC24V, 212mm/9W, 319mm/14W or 480mm/20W. Select length against the retained cavity and tested layout.
- 20W rigid edge-lit bar: DC24V, 470×24×16mm including lens, 2200lm ±10%, 10°×40° optics.
- 10W slim edge-lit bar: DC24V, 360×23×16mm including lens, 1100lm, 9°×50° optics.
Are lightbox LED modules the same as counter accent lighting?
No. Printed-graphic backlighting and counter decoration need separate optical and mounting decisions. Specify each circuit separately. A wastewater exhibition does not establish suitability for wet demonstrations; follow the selected model's installation conditions.
Before ordering
External power supplies are separate. The featured linkable family permits up to five compatible bars per run; the featured slim 10W model permits up to six after wiring checks. These are different model limits, not collection-wide rules. Check connected load and voltage drop.
Send retained-frame drawings, usable depth, print samples, old LED/driver labels, connector details and a circuit map. Request a sample retrofit review before ordering quantities; compare the full Modules range below.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
Refitting a reusable lightbox wall for a WWETT Show equipment booth? Choose internal LED bars for the retained frame, printed graphic and revised power arrangement. These components do not replace complete booth or equipment-demonstration lights.
Can I keep my existing lightbox frame when replacing the LEDs?
Survey internal depth, mounting points, supports and graphic position. Test a retained-wall section with replacement lights and the intended print: physical fit does not establish uniform illumination. Confirm the frame owner permits the mounting method.
Can I reuse the old power supply and plug-in cables?
Read driver and LED labels, not just plug shapes. For the featured DC24V bars, verify constant-voltage output, total load, cable rating, polarity and pinout before retaining any supply or cable. Mark accessible disconnection points on the revised drawing; keep storage shelves clear of service access.
Compare LED lightbox sources
- Linkable edge-lit bars: DC24V, 212mm/9W, 319mm/14W or 480mm/20W. Select length against the retained cavity and tested layout.
- 20W rigid edge-lit bar: DC24V, 470×24×16mm including lens, 2200lm ±10%, 10°×40° optics.
- 10W slim edge-lit bar: DC24V, 360×23×16mm including lens, 1100lm, 9°×50° optics.
Are lightbox LED modules the same as counter accent lighting?
No. Printed-graphic backlighting and counter decoration need separate optical and mounting decisions. Specify each circuit separately. A wastewater exhibition does not establish suitability for wet demonstrations; follow the selected model's installation conditions.
Before ordering
External power supplies are separate. The featured linkable family permits up to five compatible bars per run; the featured slim 10W model permits up to six after wiring checks. These are different model limits, not collection-wide rules. Check connected load and voltage drop.
Send retained-frame drawings, usable depth, print samples, old LED/driver labels, connector details and a circuit map. Request a sample retrofit review before ordering quantities; compare the full Modules range below.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.