Looking for Vancouver Auto Show fabric lightbox LED modules? A builder documents fabric lightbox towers at the Vancouver International Auto Show. Compare internal sources for your own independently specified display, including its wiring and access arrangements.
How do I route LED wiring without casting shadows on the fabric?
Plan cable paths outside the intended light path and allow access to connections. Test the actual printed face with wiring and frame members in place, rather than approving the light sources alone. Confirm that routing leaves the required mounting clearance.
Can I replace the connector or extend the cable on any LED bar?
Do not assume connectors are interchangeable. Check the selected product’s voltage, polarity, connector pinout, wiring requirements and permitted connections. Have the proposed extension assessed for electrical suitability before changing the circuit; never use appearance alone to choose a connector.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Does an accessible cable route prove that the complete tower is suitable?
No. Electrical access does not establish frame fit, structural stability or venue approval. Check the complete build with the responsible supplier. These modules are internal light sources; no approved replacement for a proprietary exhibit system is claimed.
Before ordering
For the three featured bars: Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Browse all LED Modules below. Send frame sections, source positions, connector photos, planned cable paths and supply details through Contact us to compare components.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
Looking for Vancouver Auto Show fabric lightbox LED modules? A builder documents fabric lightbox towers at the Vancouver International Auto Show. Compare internal sources for your own independently specified display, including its wiring and access arrangements.
How do I route LED wiring without casting shadows on the fabric?
Plan cable paths outside the intended light path and allow access to connections. Test the actual printed face with wiring and frame members in place, rather than approving the light sources alone. Confirm that routing leaves the required mounting clearance.
Can I replace the connector or extend the cable on any LED bar?
Do not assume connectors are interchangeable. Check the selected product’s voltage, polarity, connector pinout, wiring requirements and permitted connections. Have the proposed extension assessed for electrical suitability before changing the circuit; never use appearance alone to choose a connector.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Does an accessible cable route prove that the complete tower is suitable?
No. Electrical access does not establish frame fit, structural stability or venue approval. Check the complete build with the responsible supplier. These modules are internal light sources; no approved replacement for a proprietary exhibit system is claimed.
Before ordering
For the three featured bars: Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Browse all LED Modules below. Send frame sections, source positions, connector photos, planned cable paths and supply details through Contact us to compare components.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.