Coordinating an independently designed Together We Care lightbox with a fabricator in another country? Compare all 26 LED Modules products for its internal source. Agree what the remote reviewer must receive before a component order or completed display is accepted.
Give the remote reviewer a traceable lighting record
Identify the print revision, frame section, LED layout and external driver in the sample record. Photograph the illuminated face and provide the component labels and layout separately. State which drawing and print the images represent. If any of those items changes, mark the old approval as requiring review; an attractive photograph does not identify the voltage, mounting or connector used inside the box.
Carry the approved record into the venue handover
Have the installer confirm the delivered components and print against the approved record. Check the assembled face again before acceptance and record any substitutions or changed mounting details for the remote reviewer. Resolve differences with the fabricator before treating the installation as an approved repeat. Keep the handover record with the sample evidence for later replacements.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Does a remote photograph establish a module's suitability for a care setting?
No. This selection concerns printed exhibition lightboxes. It does not qualify modules for care-room lighting or medical equipment, and photographs alone cannot confirm electrical or mechanical suitability. Verify the actual display construction and component requirements.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the frame section, print revision, component schedule and remote approval records to discuss an LED-module sample for the intended lightbox.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
Coordinating an independently designed Together We Care lightbox with a fabricator in another country? Compare all 26 LED Modules products for its internal source. Agree what the remote reviewer must receive before a component order or completed display is accepted.
Give the remote reviewer a traceable lighting record
Identify the print revision, frame section, LED layout and external driver in the sample record. Photograph the illuminated face and provide the component labels and layout separately. State which drawing and print the images represent. If any of those items changes, mark the old approval as requiring review; an attractive photograph does not identify the voltage, mounting or connector used inside the box.
Carry the approved record into the venue handover
Have the installer confirm the delivered components and print against the approved record. Check the assembled face again before acceptance and record any substitutions or changed mounting details for the remote reviewer. Resolve differences with the fabricator before treating the installation as an approved repeat. Keep the handover record with the sample evidence for later replacements.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Does a remote photograph establish a module's suitability for a care setting?
No. This selection concerns printed exhibition lightboxes. It does not qualify modules for care-room lighting or medical equipment, and photographs alone cannot confirm electrical or mechanical suitability. Verify the actual display construction and component requirements.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the frame section, print revision, component schedule and remote approval records to discuss an LED-module sample for the intended lightbox.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.