Specifying an indoor illuminated graphic lightbox after Surface Design Show? A thin integrated light-guide panel and a discrete LED-bar assembly use different constructions. Compare the source architecture before transferring a surface-material sample result into a fabrication order. All 26 LED Modules products are listed below.
Identify the source construction behind the sample
Record whether the sample uses an integrated light-guide panel or discrete bars, plus the face, backing, source position and usable cavity. Check the chosen bar's dimensions including its lens, mounting parts, connectors and cable clearance. A thin finished panel's thickness is not the mounting depth available for another light-source design.
Rebuild the sample when changing source architecture
If replacing a panel system with bars, test the actual proposed face, backing and layout rather than assuming the earlier surface sample still applies. Record model, spacing, voltage, connector and driver with the result. Confirm mounting and service access; different products are comparison options, not interchangeable replacements for an exhibitor's system.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Can any LED bar replace a thin light-guide panel?
Only after the complete new assembly has been evaluated for fit and the intended visual result. These modules do not include a light-guide panel or complete lightbox, and do not establish compatibility with a named exhibitor's products or approval for a permanent architectural installation.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the existing source construction, cross-section drawing, face material, usable cavity and electrical plan for a component review. Compare all 26 products and confirm the proposed assembly before ordering.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
Specifying an indoor illuminated graphic lightbox after Surface Design Show? A thin integrated light-guide panel and a discrete LED-bar assembly use different constructions. Compare the source architecture before transferring a surface-material sample result into a fabrication order. All 26 LED Modules products are listed below.
Identify the source construction behind the sample
Record whether the sample uses an integrated light-guide panel or discrete bars, plus the face, backing, source position and usable cavity. Check the chosen bar's dimensions including its lens, mounting parts, connectors and cable clearance. A thin finished panel's thickness is not the mounting depth available for another light-source design.
Rebuild the sample when changing source architecture
If replacing a panel system with bars, test the actual proposed face, backing and layout rather than assuming the earlier surface sample still applies. Record model, spacing, voltage, connector and driver with the result. Confirm mounting and service access; different products are comparison options, not interchangeable replacements for an exhibitor's system.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Can any LED bar replace a thin light-guide panel?
Only after the complete new assembly has been evaluated for fit and the intended visual result. These modules do not include a light-guide panel or complete lightbox, and do not establish compatibility with a named exhibitor's products or approval for a permanent architectural installation.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the existing source construction, cross-section drawing, face material, usable cavity and electrical plan for a component review. Compare all 26 products and confirm the proposed assembly before ordering.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.