Sourcing LED modules for a PSANZ perinatal congress display? Start with the lightbox construction. These candidates light printed graphics inside compatible fixed frames; a rigid panel, multi-face display and inflatable kit need different mounting checks.
Can a rigid LED bar go inside an inflatable lightbox?
Do not assume it can. The featured bars need suitable fixed mounting and cable clearance. Identify the inflatable kit's original light source and maker-approved attachment before choosing a replacement; air-supported fabric is not a mounting rail. For a rigid-frame build, measure its clear depth and test the bar with the actual print.
How should I check a reusable lightbox with several lit faces?
Map each printed face and its supporting frame separately. Test adjacent faces and corners together to reveal shadows or light leaking through an unintended surface. Check LED spacing and supply load for the complete build. Preserve labelled cable routes and access to the supply so the next assembly can repeat the tested configuration.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Does a healthcare conference require medical-grade LED modules?
These products are display-lightbox components, not medical devices or clinical examination lights. Choose by the graphic frame's electrical and optical requirements. The PSANZ congress rotates across Australia and New Zealand; confirm the destination's plug and venue requirements separately from the bars' DC supply.
Before ordering
For the three featured bars: Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the structure type, frame section, dimensions of every lit face, original light-source photos and supply/connector labels. We can compare a component for a compatible rigid frame; seek the inflatable-kit maker's approval for its replacements.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
Sourcing LED modules for a PSANZ perinatal congress display? Start with the lightbox construction. These candidates light printed graphics inside compatible fixed frames; a rigid panel, multi-face display and inflatable kit need different mounting checks.
Can a rigid LED bar go inside an inflatable lightbox?
Do not assume it can. The featured bars need suitable fixed mounting and cable clearance. Identify the inflatable kit's original light source and maker-approved attachment before choosing a replacement; air-supported fabric is not a mounting rail. For a rigid-frame build, measure its clear depth and test the bar with the actual print.
How should I check a reusable lightbox with several lit faces?
Map each printed face and its supporting frame separately. Test adjacent faces and corners together to reveal shadows or light leaking through an unintended surface. Check LED spacing and supply load for the complete build. Preserve labelled cable routes and access to the supply so the next assembly can repeat the tested configuration.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Does a healthcare conference require medical-grade LED modules?
These products are display-lightbox components, not medical devices or clinical examination lights. Choose by the graphic frame's electrical and optical requirements. The PSANZ congress rotates across Australia and New Zealand; confirm the destination's plug and venue requirements separately from the bars' DC supply.
Before ordering
For the three featured bars: Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the structure type, frame section, dimensions of every lit face, original light-source photos and supply/connector labels. We can compare a component for a compatible rigid frame; seek the inflatable-kit maker's approval for its replacements.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.