LiGHT Expo London brings lighting designers, specifiers and manufacturers together. For an indoor printed lightbox, build a source specification that distinguishes component information from evidence for the finished assembly. Explore all LED Modules below and compare the exact model with your intended build.
Identify what each specification describes
Record the source model, dimensions, optics, voltage and connector from its current product information. Beside each requirement, state whether it applies to the LED component, external supply or completed assembly. Keep supporting documents attached to the exact item; do not transfer a component rating to the complete lightbox.
Tie the source schedule to a tested assembly
Have qualified personnel review the proposed power and mounting arrangement. Link the source schedule to the frame drawing, printed material and assembled sample observations. Record unverified requirements for follow-up before acceptance. A bare-source output figure does not establish finished-face brightness, uniformity or approval of the complete fixture.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Does selecting a listed LED component approve the complete lightbox?
No. Component information has a defined scope. The external supply, wiring, enclosure, mounting and finished assembly require their own applicable review; retain evidence for the actual proposed build.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the source schedule, frame drawing, printed material, requirement list, sample observations and quantity through our contact page.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
LiGHT Expo London brings lighting designers, specifiers and manufacturers together. For an indoor printed lightbox, build a source specification that distinguishes component information from evidence for the finished assembly. Explore all LED Modules below and compare the exact model with your intended build.
Identify what each specification describes
Record the source model, dimensions, optics, voltage and connector from its current product information. Beside each requirement, state whether it applies to the LED component, external supply or completed assembly. Keep supporting documents attached to the exact item; do not transfer a component rating to the complete lightbox.
Tie the source schedule to a tested assembly
Have qualified personnel review the proposed power and mounting arrangement. Link the source schedule to the frame drawing, printed material and assembled sample observations. Record unverified requirements for follow-up before acceptance. A bare-source output figure does not establish finished-face brightness, uniformity or approval of the complete fixture.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Does selecting a listed LED component approve the complete lightbox?
No. Component information has a defined scope. The external supply, wiring, enclosure, mounting and finished assembly require their own applicable review; retain evidence for the actual proposed build.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the source schedule, frame drawing, printed material, requirement list, sample observations and quantity through our contact page.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.