ISC West brings together physical and digital security exhibitors. This selection is for independent builders of indoor backlit kiosk graphics used beside separately installed demonstration hardware.
Review the lightbox with the demo hardware in place
Use the actual kiosk drawing to locate device mounting points, graphic openings, cable passages and the space available behind the print. Assemble a representative sample with the intended graphic and separately mounted demo device. Check whether mounting brackets or cable routes block the planned light source or cast unwanted shadows on the printed areas.
Keep lighting service access clear of the demonstration system
Record the tested LED positions, fixing points, connectors and driver with the kiosk section drawing. Confirm that the lightbox can be inspected or serviced without pulling on the separately installed device wiring. If a mounting plate, graphic opening or cable route changes, review the sample again before repeating the module layout.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Are these modules access-control devices or certified security-system parts?
These are internal light sources for independently designed printed lightboxes. They do not provide access control, replace readers or certify electrical or radio compatibility with demonstration equipment. Confirm model-specific voltage, mounting and connector requirements; have the separate demonstration system reviewed on its own requirements.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the kiosk section, device mounting layout, graphic openings and lighting cable route to discuss an appropriate module sample.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
ISC West brings together physical and digital security exhibitors. This selection is for independent builders of indoor backlit kiosk graphics used beside separately installed demonstration hardware.
Review the lightbox with the demo hardware in place
Use the actual kiosk drawing to locate device mounting points, graphic openings, cable passages and the space available behind the print. Assemble a representative sample with the intended graphic and separately mounted demo device. Check whether mounting brackets or cable routes block the planned light source or cast unwanted shadows on the printed areas.
Keep lighting service access clear of the demonstration system
Record the tested LED positions, fixing points, connectors and driver with the kiosk section drawing. Confirm that the lightbox can be inspected or serviced without pulling on the separately installed device wiring. If a mounting plate, graphic opening or cable route changes, review the sample again before repeating the module layout.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Are these modules access-control devices or certified security-system parts?
These are internal light sources for independently designed printed lightboxes. They do not provide access control, replace readers or certify electrical or radio compatibility with demonstration equipment. Confirm model-specific voltage, mounting and connector requirements; have the separate demonstration system reviewed on its own requirements.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the kiosk section, device mounting layout, graphic openings and lighting cable route to discuss an appropriate module sample.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.