Planning an independent IAA TRANSPORTATION exhibit with a branding lightbox alongside fabric-covered walls? Compare all 26 LED Modules products for the lightbox's internal source. Evaluate the two different print applications together without treating the unlit fabric wall as another illuminated face.
Prepare separate print references for the two applications
Label the lightbox artwork and translucent substrate separately from the wall artwork and unlit fabric. Include common logos and brand-colour areas in both samples. Test the backlit sample in its intended frame and place the wall sample beside it under the planned ambient light. Identical artwork files do not establish identical perceived colour across these constructions.
Keep the two print approvals linked to the lighting record
Record the accepted lightbox source, layout and white-light setting with both print references. Review the pair again if either substrate, ink setup or artwork changes. Adjust the lighting against the backlit sample rather than using it to correct a separate unlit wall print. Approve each application and their combined appearance; a lightbox-only photograph cannot establish the finished fabric-wall combination.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Does high CRI guarantee a match between backlit and unlit branding?
No. Printed materials, ink, lighting and viewing conditions also matter. These modules illuminate printed lightboxes; they are not video-wall pixels, decorative niche systems or vehicle lights. Check frame and electrical compatibility separately.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send both printed samples and artwork references, the lightbox section, proposed LED layout and ambient viewing conditions to discuss component trials.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
Planning an independent IAA TRANSPORTATION exhibit with a branding lightbox alongside fabric-covered walls? Compare all 26 LED Modules products for the lightbox's internal source. Evaluate the two different print applications together without treating the unlit fabric wall as another illuminated face.
Prepare separate print references for the two applications
Label the lightbox artwork and translucent substrate separately from the wall artwork and unlit fabric. Include common logos and brand-colour areas in both samples. Test the backlit sample in its intended frame and place the wall sample beside it under the planned ambient light. Identical artwork files do not establish identical perceived colour across these constructions.
Keep the two print approvals linked to the lighting record
Record the accepted lightbox source, layout and white-light setting with both print references. Review the pair again if either substrate, ink setup or artwork changes. Adjust the lighting against the backlit sample rather than using it to correct a separate unlit wall print. Approve each application and their combined appearance; a lightbox-only photograph cannot establish the finished fabric-wall combination.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Does high CRI guarantee a match between backlit and unlit branding?
No. Printed materials, ink, lighting and viewing conditions also matter. These modules illuminate printed lightboxes; they are not video-wall pixels, decorative niche systems or vehicle lights. Check frame and electrical compatibility separately.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send both printed samples and artwork references, the lightbox section, proposed LED layout and ambient viewing conditions to discuss component trials.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.