Planning co-branded backlit graphics for Elmia Subcontractor? Choose internal LED components for the actual frame sections, then check a shared fabric image across joined walls and the separate graphics on double-sided panels.
How do I check a single fabric graphic across joined lightboxes?
Assemble both frame sections and install the final shared print before approving the LED layout. Examine the join, corner and crossbar areas from the intended viewing positions. A bright sample in one frame cannot establish the appearance of the whole shared image. Keep mechanical joins clear of mounting and cable routes.
Do double-sided brand panels need the same LED arrangement?
Not necessarily. Check the clear distance to both transmitting faces, mounting positions and source direction. Compare each brand’s final artwork under the proposed light rather than assuming the same fabric name or nominal white tone produces the same result. Frame sections can require different arrangements within one booth.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Can I reuse LED bars when subsidiary branding changes?
Reuse is possible only after checking the new print, frame condition, connections and power load. Label the LED layout and compatible supply for each section so components are not mixed during reassembly. Test the connected backwall and both faces again; a new print does not guarantee unchanged illumination or replacement-module fit.
Before ordering
For the three featured bars: Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Compare all 26 options below. Send each frame section, joined-graphic layout, single- or double-sided construction and existing power details for a component quote. BOOTH LIGHTS bars are separate components; compatibility with an existing branded frame must be confirmed.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
Planning co-branded backlit graphics for Elmia Subcontractor? Choose internal LED components for the actual frame sections, then check a shared fabric image across joined walls and the separate graphics on double-sided panels.
How do I check a single fabric graphic across joined lightboxes?
Assemble both frame sections and install the final shared print before approving the LED layout. Examine the join, corner and crossbar areas from the intended viewing positions. A bright sample in one frame cannot establish the appearance of the whole shared image. Keep mechanical joins clear of mounting and cable routes.
Do double-sided brand panels need the same LED arrangement?
Not necessarily. Check the clear distance to both transmitting faces, mounting positions and source direction. Compare each brand’s final artwork under the proposed light rather than assuming the same fabric name or nominal white tone produces the same result. Frame sections can require different arrangements within one booth.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Can I reuse LED bars when subsidiary branding changes?
Reuse is possible only after checking the new print, frame condition, connections and power load. Label the LED layout and compatible supply for each section so components are not mixed during reassembly. Test the connected backwall and both faces again; a new print does not guarantee unchanged illumination or replacement-module fit.
Before ordering
For the three featured bars: Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Compare all 26 options below. Send each frame section, joined-graphic layout, single- or double-sided construction and existing power details for a component quote. BOOTH LIGHTS bars are separate components; compatibility with an existing branded frame must be confirmed.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.