Specifying a square printed lightbox for an independent AGRITECHNICA exhibit? Compare all 26 LED Modules products. For a proposed edge-lit layout, this selection focuses on what happens where light from adjacent edges meets, rather than selecting a source from wattage alone.
Label each edge-lighting bank on the frame drawing
Show the proposed bar positions, lenses and connectors along each active edge. Identify which banks meet at each corner and which edges contain no source. Check physical clearance at those junctions before fixing the layout. A square graphic does not establish that the same bar count or orientation suits every edge.
Compare individual banks and the combined corner pattern
With a suitably planned trial circuit, compare each bank's illumination and then the combined arrangement using the same print and viewing position. Record bright corner patches, edge bands and centre coverage separately. Retain the accepted bank positions and combined sample with the component list. Repeat the combined trial after changing a bar position; an acceptable individual bank does not prove an acceptable corner overlap.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Does adding more edge bars guarantee a better square lightbox?
No. Judge the complete printed assembly, including corners and centre. These are internal lightbox sources, not agricultural-machine lights or complete exhibit frames. Confirm actual mounting space, wiring and power requirements for each selected model.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the square frame section, labelled edge-bank plan, printed sample and individual versus combined trial observations to discuss LED component options.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
Specifying a square printed lightbox for an independent AGRITECHNICA exhibit? Compare all 26 LED Modules products. For a proposed edge-lit layout, this selection focuses on what happens where light from adjacent edges meets, rather than selecting a source from wattage alone.
Label each edge-lighting bank on the frame drawing
Show the proposed bar positions, lenses and connectors along each active edge. Identify which banks meet at each corner and which edges contain no source. Check physical clearance at those junctions before fixing the layout. A square graphic does not establish that the same bar count or orientation suits every edge.
Compare individual banks and the combined corner pattern
With a suitably planned trial circuit, compare each bank's illumination and then the combined arrangement using the same print and viewing position. Record bright corner patches, edge bands and centre coverage separately. Retain the accepted bank positions and combined sample with the component list. Repeat the combined trial after changing a bar position; an acceptable individual bank does not prove an acceptable corner overlap.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Does adding more edge bars guarantee a better square lightbox?
No. Judge the complete printed assembly, including corners and centre. These are internal lightbox sources, not agricultural-machine lights or complete exhibit frames. Confirm actual mounting space, wiring and power requirements for each selected model.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the square frame section, labelled edge-bank plan, printed sample and individual versus combined trial observations to discuss LED component options.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.