Looking for Toolfair lightbox LED modules? Compare internal sources for backlit graphics beside physical tool displays. A stand maker reports lightboxes highlighting graphics at Toolfair; your own frame, print and product-rack arrangement still need to be specified.
Will tools and racks cast shadows on my lightbox graphic?
Photograph or sketch where the products, racks and frame cross the light path. A rack inside the box can interrupt backlighting; a product in front can hide the printed message from visitors. Test the actual arrangement before choosing source positions. Extra wattage does not remove a physical obstruction.
Should the same LEDs light the graphic and the tools?
Internal modules illuminate a suitable translucent lightbox face. Lighting tools outside the box is a separate task, requiring its own beam direction and glare checks. Compare LED optics for the graphic first, then plan any product lighting around the visitor’s view and the stand’s electrical arrangement.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Can I reuse the same module layout at every roadshow stop?
Reuse depends on keeping a verified frame, printed-face material and electrical arrangement. Changing racks, graphic size or internal clearance can require a new layout test. Check connections after assembly and confirm each venue’s requirements instead of assuming a previous setup covers every stop.
Before ordering
For the three featured bars: Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Browse all LED Modules below. Send lightbox dimensions, printed material, rack positions and a view of the tool display through Contact us to compare sources.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
-
20W Rigid LED Light Box Bars – 2200lm, DC24V, 10-Pack+ -
12W Dual-CCT Switchable LED Lightbox Bar – 24V -
10W Slim Edge-Lit LED Lightbox Bar – 360mm, 9°×50° Lens -
12W/18W LED Module for MODULAP Fabric Lightbox -
45W High-Output Edge-Lit LED Bar for Large Light Boxes – 958mm, 4400lm -
DC24V Linkable Edge-Lit LED Light Box Bars for SEG Displays -
12W Compact LED Lightbox Bar – 313mm, 24V, 6 LEDs, 1200lm -
18W LED Lightbox Bar – 585mm, 24V, 9 LEDs, 14°×50° Optical Lens -
10W DC Plug LED Lightbox Bar – 360mm, 24V, 15°×45° Optical Lens -
12W Dual-Angle LED Lightbox Bar – 517mm, 24V, 15°×45° Optical Lens -
22W–32W Aluminum Profile LED Lightbox Modules – 10-Pack+ -
10W Edge-Lit LED Light Box Bars – 360mm, 10-Pack+ -
Edge-Lit LED Module for Light Boxes – 3.5W/7W/21W, ETL Listed, DC24V -
DC Plug LED Backlight Bar for Light Boxes – 3W/6W/9W Modular System -
8W Corner LED Module, Compact Edge-Lit Light Source for SEG Fabric Light Boxes – 202mm, 10-Pack+ -
30W RGBW LED Light Bars – 400mm, 10-Pack+ -
27.5W Optical Edge-Lit LED Light Box Bars – 10-Pack+ -
14W 313mm-Long Edge-Lit LED Light Box Bars – 1540lm -
32W 4-in-1 RGBW Edge-Lit LED Light Box Bars – 10-Pack+ -
24W RGB Edge-Lit LED Bar for SEG Light Boxes & Displays -
Side-Lit LED Module for MODULAP Systems -
7W DC24V Side-Lit LED Lightbox Module – Optical Lens -
7W 200mm Mini LED Light Box Bar – 770lm, DC24V -
13W Edge-Lit LED Lightbox Bar – 360mm, 1430lm, ETL Listed
Looking for Toolfair lightbox LED modules? Compare internal sources for backlit graphics beside physical tool displays. A stand maker reports lightboxes highlighting graphics at Toolfair; your own frame, print and product-rack arrangement still need to be specified.
Will tools and racks cast shadows on my lightbox graphic?
Photograph or sketch where the products, racks and frame cross the light path. A rack inside the box can interrupt backlighting; a product in front can hide the printed message from visitors. Test the actual arrangement before choosing source positions. Extra wattage does not remove a physical obstruction.
Should the same LEDs light the graphic and the tools?
Internal modules illuminate a suitable translucent lightbox face. Lighting tools outside the box is a separate task, requiring its own beam direction and glare checks. Compare LED optics for the graphic first, then plan any product lighting around the visitor’s view and the stand’s electrical arrangement.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Can I reuse the same module layout at every roadshow stop?
Reuse depends on keeping a verified frame, printed-face material and electrical arrangement. Changing racks, graphic size or internal clearance can require a new layout test. Check connections after assembly and confirm each venue’s requirements instead of assuming a previous setup covers every stop.
Before ordering
For the three featured bars: Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Browse all LED Modules below. Send lightbox dimensions, printed material, rack positions and a view of the tool display through Contact us to compare sources.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.