The NATDA Trailer Show brings together trailer dealers, manufacturers and suppliers. This selection helps independent exhibit builders compare internal LED sources for printed lightbox frames intended to be used in different display orientations.
Treat a change of orientation as a new component-layout review
Where a frame is designed for both overhead and floor-standing use, draw the intended configuration before selecting its light sources. Identify how module fasteners, cable entries and external-driver positions will be accessed in that orientation. Check the available space behind each printed face; reusing a frame does not establish that its previous module layout and cable routing remain suitable.
Repeat the sample in the intended display configuration
Test the actual graphics, backing and LED spacing with the proposed mounting arrangement. Label the accepted orientation, module positions and connector access in the component record. If conversion moves the sources, supply or cable passages, repeat the affected sample and review the wiring arrangement before assembly. Retain separate installation information for each approved configuration instead of applying one unlabelled layout to both.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Do these LED modules make a hanging frame safe to use on the floor?
The modules are light sources, not conversion hardware or structural approval. Have the frame, supports and intended installation reviewed separately; any supplier's conversion kit or existing frame requires its own suitability check. Confirm the chosen module's electrical and mounting requirements for the lightbox.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the intended orientation, frame section, module fasteners and cable-entry drawing to discuss a component sample.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
-
20W Rigid LED Light Box Bars – 2200lm, DC24V, 10-Pack+ -
12W Dual-CCT Switchable LED Lightbox Bar – 24V -
10W Slim Edge-Lit LED Lightbox Bar – 360mm, 9°×50° Lens -
12W/18W LED Module for MODULAP Fabric Lightbox -
45W High-Output Edge-Lit LED Bar for Large Light Boxes – 958mm, 4400lm -
DC24V Linkable Edge-Lit LED Light Box Bars for SEG Displays -
12W Compact LED Lightbox Bar – 313mm, 24V, 6 LEDs, 1200lm -
18W LED Lightbox Bar – 585mm, 24V, 9 LEDs, 14°×50° Optical Lens -
10W DC Plug LED Lightbox Bar – 360mm, 24V, 15°×45° Optical Lens -
12W Dual-Angle LED Lightbox Bar – 517mm, 24V, 15°×45° Optical Lens -
22W–32W Aluminum Profile LED Lightbox Modules – 10-Pack+ -
10W Edge-Lit LED Light Box Bars – 360mm, 10-Pack+ -
Edge-Lit LED Module for Light Boxes – 3.5W/7W/21W, ETL Listed, DC24V -
DC Plug LED Backlight Bar for Light Boxes – 3W/6W/9W Modular System -
8W Corner LED Module, Compact Edge-Lit Light Source for SEG Fabric Light Boxes – 202mm, 10-Pack+ -
30W RGBW LED Light Bars – 400mm, 10-Pack+ -
27.5W Optical Edge-Lit LED Light Box Bars – 10-Pack+ -
14W 313mm-Long Edge-Lit LED Light Box Bars – 1540lm -
32W 4-in-1 RGBW Edge-Lit LED Light Box Bars – 10-Pack+ -
24W RGB Edge-Lit LED Bar for SEG Light Boxes & Displays -
Side-Lit LED Module for MODULAP Systems -
7W DC24V Side-Lit LED Lightbox Module – Optical Lens -
7W 200mm Mini LED Light Box Bar – 770lm, DC24V -
13W Edge-Lit LED Lightbox Bar – 360mm, 1430lm, ETL Listed
The NATDA Trailer Show brings together trailer dealers, manufacturers and suppliers. This selection helps independent exhibit builders compare internal LED sources for printed lightbox frames intended to be used in different display orientations.
Treat a change of orientation as a new component-layout review
Where a frame is designed for both overhead and floor-standing use, draw the intended configuration before selecting its light sources. Identify how module fasteners, cable entries and external-driver positions will be accessed in that orientation. Check the available space behind each printed face; reusing a frame does not establish that its previous module layout and cable routing remain suitable.
Repeat the sample in the intended display configuration
Test the actual graphics, backing and LED spacing with the proposed mounting arrangement. Label the accepted orientation, module positions and connector access in the component record. If conversion moves the sources, supply or cable passages, repeat the affected sample and review the wiring arrangement before assembly. Retain separate installation information for each approved configuration instead of applying one unlabelled layout to both.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Do these LED modules make a hanging frame safe to use on the floor?
The modules are light sources, not conversion hardware or structural approval. Have the frame, supports and intended installation reviewed separately; any supplier's conversion kit or existing frame requires its own suitability check. Confirm the chosen module's electrical and mounting requirements for the lightbox.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the intended orientation, frame section, module fasteners and cable-entry drawing to discuss a component sample.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.