ISA BuildU combines sign-cabinet and LED installation training. For independent indoor lightbox builds, use a clear dimension reference before comparing LED bar layouts. Browse all LED Modules below for the actual frame and graphic.
Mark where each layout measurement starts
Identify an internal frame edge as the reference and mark the measurement direction. State whether each offset locates the housing edge, lens center or mounting point. Keep the same reference on the drawing and physical sample; dimensions from different edges cannot be compared without reconciling their origins.
Compare the drawing with the unpowered assembly
Measure the selected bar, connectors and mounting arrangement in the actual frame. Record measured offsets rather than assuming the lens center coincides with the housing edge. Have qualified personnel check mounting and wiring before illumination. Retain the reference marks and sample observations when revising the layout; no universal spacing is implied.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Are a housing-edge offset and a lens-center offset interchangeable?
No. Identify the measured feature and reference edge before comparing positions. Check actual component dimensions and the assembled sample instead of treating differently referenced measurements as equal.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the marked frame drawing, measurement direction, referenced features, measured offsets, LED candidates, sample observations and quantity through our contact page.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
-
20W Rigid LED Light Box Bars – 2200lm, DC24V, 10-Pack+ -
12W Dual-CCT Switchable LED Lightbox Bar – 24V -
10W Slim Edge-Lit LED Lightbox Bar – 360mm, 9°×50° Lens -
12W/18W LED Module for MODULAP Fabric Lightbox -
45W High-Output Edge-Lit LED Bar for Large Light Boxes – 958mm, 4400lm -
DC24V Linkable Edge-Lit LED Light Box Bars for SEG Displays -
12W Compact LED Lightbox Bar – 313mm, 24V, 6 LEDs, 1200lm -
18W LED Lightbox Bar – 585mm, 24V, 9 LEDs, 14°×50° Optical Lens -
10W DC Plug LED Lightbox Bar – 360mm, 24V, 15°×45° Optical Lens -
12W Dual-Angle LED Lightbox Bar – 517mm, 24V, 15°×45° Optical Lens -
22W–32W Aluminum Profile LED Lightbox Modules – 10-Pack+ -
10W Edge-Lit LED Light Box Bars – 360mm, 10-Pack+ -
Edge-Lit LED Module for Light Boxes – 3.5W/7W/21W, ETL Listed, DC24V -
DC Plug LED Backlight Bar for Light Boxes – 3W/6W/9W Modular System -
8W Corner LED Module, Compact Edge-Lit Light Source for SEG Fabric Light Boxes – 202mm, 10-Pack+ -
30W RGBW LED Light Bars – 400mm, 10-Pack+ -
27.5W Optical Edge-Lit LED Light Box Bars – 10-Pack+ -
14W 313mm-Long Edge-Lit LED Light Box Bars – 1540lm -
32W 4-in-1 RGBW Edge-Lit LED Light Box Bars – 10-Pack+ -
24W RGB Edge-Lit LED Bar for SEG Light Boxes & Displays -
Side-Lit LED Module for MODULAP Systems -
7W DC24V Side-Lit LED Lightbox Module – Optical Lens -
7W 200mm Mini LED Light Box Bar – 770lm, DC24V -
13W Edge-Lit LED Lightbox Bar – 360mm, 1430lm, ETL Listed
ISA BuildU combines sign-cabinet and LED installation training. For independent indoor lightbox builds, use a clear dimension reference before comparing LED bar layouts. Browse all LED Modules below for the actual frame and graphic.
Mark where each layout measurement starts
Identify an internal frame edge as the reference and mark the measurement direction. State whether each offset locates the housing edge, lens center or mounting point. Keep the same reference on the drawing and physical sample; dimensions from different edges cannot be compared without reconciling their origins.
Compare the drawing with the unpowered assembly
Measure the selected bar, connectors and mounting arrangement in the actual frame. Record measured offsets rather than assuming the lens center coincides with the housing edge. Have qualified personnel check mounting and wiring before illumination. Retain the reference marks and sample observations when revising the layout; no universal spacing is implied.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Are a housing-edge offset and a lens-center offset interchangeable?
No. Identify the measured feature and reference edge before comparing positions. Check actual component dimensions and the assembled sample instead of treating differently referenced measurements as equal.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the marked frame drawing, measurement direction, referenced features, measured offsets, LED candidates, sample observations and quantity through our contact page.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.