EFI offers printer demonstrations, and its sign-and-display guidance includes double-sided backlit printing and printer proofing lights. This independent selection helps sign shops choose internal LED modules for a finished lightbox without confusing print alignment with light distribution.
Which backlit sample should I take to EFI Ignite?
Bring a labelled front-and-reverse print sample and the intended film or fabric. Ask the print provider to identify any white, clear or blockout layers. Keep the approved sample with its layer record, then compare it in the actual indoor cabinet at the recorded LED layout, CCT and driver settings. Match that assembly before ordering replacement bars; a printer demonstration alone does not specify the finished lightbox.
Check print registration and illumination separately
Keep the front and reverse print orientation with the sample. First assess the printed layers under a stable transmitted-light reference agreed with your print provider. Then test the approved face in the intended cabinet with its actual depth, diffuser, LED positions and power supply. Record print defects and lighting defects separately before changing a component.
Choose the light source for the display
- DC24V linkable edge-lit bars: 212mm/9W, 319mm/14W or 480mm/20W for modular lightbox builds.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 20W DC24V rigid lightbox bar: 470mm, 2200lm ±10%, for tested indoor SEG and illuminated-sign layouts.
- 7W DC24V compact lightbox bar: 200mm, 770lm, 200×23×16mm body for short frame sections. Check the Molex 5557 / Mini-Fit Jr. connector family, mating pinout and fit before replacement.
Can brighter LEDs correct a misregistered double-sided backlit print?
No. More light does not move printed layers into alignment. Ask the print provider to verify the front-to-back registration and intended layer construction. Choose LED output and spacing only after the graphic has passed its own alignment check.
How can I compare graphic defects with lightbox hot spots?
Compare a suitable unprinted transmitting reference and the graphic in the same fixture, keeping depth, LED positions and electrical settings unchanged. A repeatable pattern in the unprinted reference suggests a lighting or enclosure issue; a defect appearing only with the print needs a face and printing review. This comparison is a starting point, not a conclusive diagnosis.
Can the printer’s proofing LEDs specify my lightbox components?
No. Printer proofing lights and printing-table lighting do not establish the required bar type, voltage, connector or quantity in your finished cabinet. These products are independent display light sources, not EFI printer parts or UV-curing replacements. Specify the complete lightbox test and exact electrical interfaces before ordering.
Before ordering
LED Modules illuminate a printed face inside a lightbox; they are not complete signs. Confirm connector polarity, driver capacity, thermal conditions and connection limits. Check the selected bar length and product pack quantity. Do not assume outdoor or moisture suitability from a retrofit application.
Send cabinet photos, internal dimensions, frame drawings, the existing driver specification and proposed product links through our contact page to discuss a trial selection.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
-
12W/18W LED Module for MODULAP Fabric Lightbox -
45W High-Output Edge-Lit LED Bar for Large Light Boxes – 958mm, 4400lm -
DC24V Linkable Edge-Lit LED Light Box Bars for SEG Displays -
Side-Lit LED Module for MODULAP Systems -
20W Rigid LED Light Box Bars – 2200lm, DC24V, 10-Pack+ -
10W Slim Edge-Lit LED Lightbox Bar – 360mm, 9°×50° Lens -
12W Compact LED Lightbox Bar – 313mm, 24V, 6 LEDs, 1200lm -
18W LED Lightbox Bar – 585mm, 24V, 9 LEDs, 14°×50° Optical Lens -
10W DC Plug LED Lightbox Bar – 360mm, 24V, 15°×45° Optical Lens -
12W Dual-Angle LED Lightbox Bar – 517mm, 24V, 15°×45° Optical Lens -
22W–32W Aluminum Profile LED Lightbox Modules – 10-Pack+ -
10W Edge-Lit LED Light Box Bars – 360mm, 10-Pack+ -
Edge-Lit LED Module for Light Boxes – 3.5W/7W/21W, ETL Listed, DC24V -
DC Plug LED Backlight Bar for Light Boxes – 3W/6W/9W Modular System -
8W Corner LED Module, Compact Edge-Lit Light Source for SEG Fabric Light Boxes – 202mm, 10-Pack+ -
30W RGBW LED Light Bars – 400mm, 10-Pack+ -
27.5W Optical Edge-Lit LED Light Box Bars – 10-Pack+ -
14W 313mm-Long Edge-Lit LED Light Box Bars – 1540lm -
32W 4-in-1 RGBW Edge-Lit LED Light Box Bars – 10-Pack+ -
24W RGB Edge-Lit LED Bar for SEG Light Boxes & Displays -
7W DC24V Side-Lit LED Lightbox Module – Optical Lens -
7W 200mm Mini LED Light Box Bar – 770lm, DC24V -
13W Edge-Lit LED Lightbox Bar – 360mm, 1430lm, ETL Listed -
12W Dual-CCT Switchable LED Lightbox Bar – 24V
EFI offers printer demonstrations, and its sign-and-display guidance includes double-sided backlit printing and printer proofing lights. This independent selection helps sign shops choose internal LED modules for a finished lightbox without confusing print alignment with light distribution.
Which backlit sample should I take to EFI Ignite?
Bring a labelled front-and-reverse print sample and the intended film or fabric. Ask the print provider to identify any white, clear or blockout layers. Keep the approved sample with its layer record, then compare it in the actual indoor cabinet at the recorded LED layout, CCT and driver settings. Match that assembly before ordering replacement bars; a printer demonstration alone does not specify the finished lightbox.
Check print registration and illumination separately
Keep the front and reverse print orientation with the sample. First assess the printed layers under a stable transmitted-light reference agreed with your print provider. Then test the approved face in the intended cabinet with its actual depth, diffuser, LED positions and power supply. Record print defects and lighting defects separately before changing a component.
Choose the light source for the display
- DC24V linkable edge-lit bars: 212mm/9W, 319mm/14W or 480mm/20W for modular lightbox builds.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 20W DC24V rigid lightbox bar: 470mm, 2200lm ±10%, for tested indoor SEG and illuminated-sign layouts.
- 7W DC24V compact lightbox bar: 200mm, 770lm, 200×23×16mm body for short frame sections. Check the Molex 5557 / Mini-Fit Jr. connector family, mating pinout and fit before replacement.
Can brighter LEDs correct a misregistered double-sided backlit print?
No. More light does not move printed layers into alignment. Ask the print provider to verify the front-to-back registration and intended layer construction. Choose LED output and spacing only after the graphic has passed its own alignment check.
How can I compare graphic defects with lightbox hot spots?
Compare a suitable unprinted transmitting reference and the graphic in the same fixture, keeping depth, LED positions and electrical settings unchanged. A repeatable pattern in the unprinted reference suggests a lighting or enclosure issue; a defect appearing only with the print needs a face and printing review. This comparison is a starting point, not a conclusive diagnosis.
Can the printer’s proofing LEDs specify my lightbox components?
No. Printer proofing lights and printing-table lighting do not establish the required bar type, voltage, connector or quantity in your finished cabinet. These products are independent display light sources, not EFI printer parts or UV-curing replacements. Specify the complete lightbox test and exact electrical interfaces before ordering.
Before ordering
LED Modules illuminate a printed face inside a lightbox; they are not complete signs. Confirm connector polarity, driver capacity, thermal conditions and connection limits. Check the selected bar length and product pack quantity. Do not assume outdoor or moisture suitability from a retrofit application.
Send cabinet photos, internal dimensions, frame drawings, the existing driver specification and proposed product links through our contact page to discuss a trial selection.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.