DAC is a conference and exhibition for electronic design automation and chip-to-system design. This selection supports independent exhibit builders specifying printed graphic lightboxes alongside separately supplied demonstration equipment.
Identify the lightbox load as a separate procurement item
Prepare a component list for the printed lightbox: chosen module, quantity, rated voltage, connector and compatible external driver. Keep this list distinct from computers, display screens and demonstration hardware. Compare a representative illuminated print using the proposed lightbox supply, rather than inferring its power requirements from a demo workstation or an unrelated display.
Record what the graphic-lightbox sample actually verifies
Label the tested lightbox driver and module run in the sample record, along with the printed face and layout. Have the overall exhibit power plan reviewed against the separate equipment requirements before installation. If the demonstration equipment or supply arrangement changes, review those boundaries again; a good-looking print sample does not establish the electrical performance of the demonstration system.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Do these lightbox modules certify EMC or replace demo-screen backlights?
These products are internal light sources for independently designed printed lightboxes. They are not computer-display replacement parts, EDA hardware or a guarantee of electromagnetic compatibility with nearby equipment. Confirm the chosen module’s voltage, connector and driver requirements, and review the demonstration system separately.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the graphic-lightbox dimensions, module quantity, proposed driver and separately listed demo equipment to discuss a component sample.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
-
20W Rigid LED Light Box Bars – 2200lm, DC24V, 10-Pack+ -
12W Dual-CCT Switchable LED Lightbox Bar – 24V -
10W Slim Edge-Lit LED Lightbox Bar – 360mm, 9°×50° Lens -
12W/18W LED Module for MODULAP Fabric Lightbox -
45W High-Output Edge-Lit LED Bar for Large Light Boxes – 958mm, 4400lm -
DC24V Linkable Edge-Lit LED Light Box Bars for SEG Displays -
12W Compact LED Lightbox Bar – 313mm, 24V, 6 LEDs, 1200lm -
18W LED Lightbox Bar – 585mm, 24V, 9 LEDs, 14°×50° Optical Lens -
10W DC Plug LED Lightbox Bar – 360mm, 24V, 15°×45° Optical Lens -
12W Dual-Angle LED Lightbox Bar – 517mm, 24V, 15°×45° Optical Lens -
22W–32W Aluminum Profile LED Lightbox Modules – 10-Pack+ -
10W Edge-Lit LED Light Box Bars – 360mm, 10-Pack+ -
Edge-Lit LED Module for Light Boxes – 3.5W/7W/21W, ETL Listed, DC24V -
DC Plug LED Backlight Bar for Light Boxes – 3W/6W/9W Modular System -
8W Corner LED Module, Compact Edge-Lit Light Source for SEG Fabric Light Boxes – 202mm, 10-Pack+ -
30W RGBW LED Light Bars – 400mm, 10-Pack+ -
27.5W Optical Edge-Lit LED Light Box Bars – 10-Pack+ -
14W 313mm-Long Edge-Lit LED Light Box Bars – 1540lm -
32W 4-in-1 RGBW Edge-Lit LED Light Box Bars – 10-Pack+ -
24W RGB Edge-Lit LED Bar for SEG Light Boxes & Displays -
Side-Lit LED Module for MODULAP Systems -
7W DC24V Side-Lit LED Lightbox Module – Optical Lens -
7W 200mm Mini LED Light Box Bar – 770lm, DC24V -
13W Edge-Lit LED Lightbox Bar – 360mm, 1430lm, ETL Listed
DAC is a conference and exhibition for electronic design automation and chip-to-system design. This selection supports independent exhibit builders specifying printed graphic lightboxes alongside separately supplied demonstration equipment.
Identify the lightbox load as a separate procurement item
Prepare a component list for the printed lightbox: chosen module, quantity, rated voltage, connector and compatible external driver. Keep this list distinct from computers, display screens and demonstration hardware. Compare a representative illuminated print using the proposed lightbox supply, rather than inferring its power requirements from a demo workstation or an unrelated display.
Record what the graphic-lightbox sample actually verifies
Label the tested lightbox driver and module run in the sample record, along with the printed face and layout. Have the overall exhibit power plan reviewed against the separate equipment requirements before installation. If the demonstration equipment or supply arrangement changes, review those boundaries again; a good-looking print sample does not establish the electrical performance of the demonstration system.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Do these lightbox modules certify EMC or replace demo-screen backlights?
These products are internal light sources for independently designed printed lightboxes. They are not computer-display replacement parts, EDA hardware or a guarantee of electromagnetic compatibility with nearby equipment. Confirm the chosen module’s voltage, connector and driver requirements, and review the demonstration system separately.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the graphic-lightbox dimensions, module quantity, proposed driver and separately listed demo equipment to discuss a component sample.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.