Looking for Toronto Auto Show fabric lightbox LED modules? Exhibit builders have used fabric lightbox towers at the Canadian International AutoShow. Compare internal LED sources for your independently specified frame and printed face.
Which LED bars should I choose for a tall fabric lightbox?
Height alone cannot determine the module. Compare usable depth, bar dimensions, lens direction, mounting and the complete printed face. An edge-lit layout and a backlit layout require different source positions; test the proposed arrangement at full height.
How many LED modules does a lightbox tower need?
There is no universal quantity based only on height. Use the actual face dimensions, frame section and selected bar specifications to develop a layout. Check uniformity over the whole print, then calculate the electrical load and supply requirements for that verified arrangement.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Are these modules approved replacements for the tower in the exhibit case?
No system-specific fit or approval is claimed. Confirm mounting, clearance, voltage, polarity and connectors for your own build. Structural stability and venue installation requirements need separate review by the responsible supplier.
Before ordering
For the three featured bars: Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Browse all LED Modules below. Send tower dimensions, frame section, print material and proposed source positions through Contact us for component comparison.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
-
20W Rigid LED Light Box Bars – 2200lm, DC24V, 10-Pack+ -
12W Dual-CCT Switchable LED Lightbox Bar – 24V -
10W Slim Edge-Lit LED Lightbox Bar – 360mm, 9°×50° Lens -
12W/18W LED Module for MODULAP Fabric Lightbox -
45W High-Output Edge-Lit LED Bar for Large Light Boxes – 958mm, 4400lm -
DC24V Linkable Edge-Lit LED Light Box Bars for SEG Displays -
12W Compact LED Lightbox Bar – 313mm, 24V, 6 LEDs, 1200lm -
18W LED Lightbox Bar – 585mm, 24V, 9 LEDs, 14°×50° Optical Lens -
10W DC Plug LED Lightbox Bar – 360mm, 24V, 15°×45° Optical Lens -
12W Dual-Angle LED Lightbox Bar – 517mm, 24V, 15°×45° Optical Lens -
22W–32W Aluminum Profile LED Lightbox Modules – 10-Pack+ -
10W Edge-Lit LED Light Box Bars – 360mm, 10-Pack+ -
Edge-Lit LED Module for Light Boxes – 3.5W/7W/21W, ETL Listed, DC24V -
DC Plug LED Backlight Bar for Light Boxes – 3W/6W/9W Modular System -
8W Corner LED Module, Compact Edge-Lit Light Source for SEG Fabric Light Boxes – 202mm, 10-Pack+ -
30W RGBW LED Light Bars – 400mm, 10-Pack+ -
27.5W Optical Edge-Lit LED Light Box Bars – 10-Pack+ -
14W 313mm-Long Edge-Lit LED Light Box Bars – 1540lm -
32W 4-in-1 RGBW Edge-Lit LED Light Box Bars – 10-Pack+ -
24W RGB Edge-Lit LED Bar for SEG Light Boxes & Displays -
Side-Lit LED Module for MODULAP Systems -
7W DC24V Side-Lit LED Lightbox Module – Optical Lens -
7W 200mm Mini LED Light Box Bar – 770lm, DC24V -
13W Edge-Lit LED Lightbox Bar – 360mm, 1430lm, ETL Listed
Looking for Toronto Auto Show fabric lightbox LED modules? Exhibit builders have used fabric lightbox towers at the Canadian International AutoShow. Compare internal LED sources for your independently specified frame and printed face.
Which LED bars should I choose for a tall fabric lightbox?
Height alone cannot determine the module. Compare usable depth, bar dimensions, lens direction, mounting and the complete printed face. An edge-lit layout and a backlit layout require different source positions; test the proposed arrangement at full height.
How many LED modules does a lightbox tower need?
There is no universal quantity based only on height. Use the actual face dimensions, frame section and selected bar specifications to develop a layout. Check uniformity over the whole print, then calculate the electrical load and supply requirements for that verified arrangement.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Are these modules approved replacements for the tower in the exhibit case?
No system-specific fit or approval is claimed. Confirm mounting, clearance, voltage, polarity and connectors for your own build. Structural stability and venue installation requirements need separate review by the responsible supplier.
Before ordering
For the three featured bars: Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Browse all LED Modules below. Send tower dimensions, frame section, print material and proposed source positions through Contact us for component comparison.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.