A4M Longevity SpringFest, also known as the A4M Spring Congress, includes supplier exhibits. This selection supports independent builders specifying backlit fabric graphics on booth towers that also contain storage.
Keep the lightbox cavity distinct from the storage space
Measure the lighting space remaining after the storage compartment, partition, door hardware and cable passages are included. Specify the mounting surface and backing for the illuminated graphic; the tower's overall depth is not the available LED-to-fabric distance. Check that normal access to storage will not move cables or place stored items into the lighting cavity.
Review the tower in its intended storage configuration
Test the actual printed fabric with the proposed partition and doors installed. Review the face with storage configured as intended, and check whether partition edges or access details introduce shadows or light leakage. Record the module positions and the boundary that must stay clear. Recheck the sample if the storage layout changes, rather than relying on an empty-frame lighting test.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Does a storage-tower lightbox need a medical-device light source?
This selection concerns indoor printed booth graphics. It does not qualify modules for medical devices, treatment equipment or clinical illumination. Confirm each chosen component's voltage, connector, driver and environmental requirements for the lightbox itself.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the tower section drawing, storage partition, access-door details and fabric sample to discuss suitable lightbox component samples.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
-
20W Rigid LED Light Box Bars – 2200lm, DC24V, 10-Pack+ -
12W Dual-CCT Switchable LED Lightbox Bar – 24V -
10W Slim Edge-Lit LED Lightbox Bar – 360mm, 9°×50° Lens -
12W/18W LED Module for MODULAP Fabric Lightbox -
45W High-Output Edge-Lit LED Bar for Large Light Boxes – 958mm, 4400lm -
DC24V Linkable Edge-Lit LED Light Box Bars for SEG Displays -
12W Compact LED Lightbox Bar – 313mm, 24V, 6 LEDs, 1200lm -
18W LED Lightbox Bar – 585mm, 24V, 9 LEDs, 14°×50° Optical Lens -
10W DC Plug LED Lightbox Bar – 360mm, 24V, 15°×45° Optical Lens -
12W Dual-Angle LED Lightbox Bar – 517mm, 24V, 15°×45° Optical Lens -
22W–32W Aluminum Profile LED Lightbox Modules – 10-Pack+ -
10W Edge-Lit LED Light Box Bars – 360mm, 10-Pack+ -
Edge-Lit LED Module for Light Boxes – 3.5W/7W/21W, ETL Listed, DC24V -
DC Plug LED Backlight Bar for Light Boxes – 3W/6W/9W Modular System -
8W Corner LED Module, Compact Edge-Lit Light Source for SEG Fabric Light Boxes – 202mm, 10-Pack+ -
30W RGBW LED Light Bars – 400mm, 10-Pack+ -
27.5W Optical Edge-Lit LED Light Box Bars – 10-Pack+ -
14W 313mm-Long Edge-Lit LED Light Box Bars – 1540lm -
32W 4-in-1 RGBW Edge-Lit LED Light Box Bars – 10-Pack+ -
24W RGB Edge-Lit LED Bar for SEG Light Boxes & Displays -
Side-Lit LED Module for MODULAP Systems -
7W DC24V Side-Lit LED Lightbox Module – Optical Lens -
7W 200mm Mini LED Light Box Bar – 770lm, DC24V -
13W Edge-Lit LED Lightbox Bar – 360mm, 1430lm, ETL Listed
A4M Longevity SpringFest, also known as the A4M Spring Congress, includes supplier exhibits. This selection supports independent builders specifying backlit fabric graphics on booth towers that also contain storage.
Keep the lightbox cavity distinct from the storage space
Measure the lighting space remaining after the storage compartment, partition, door hardware and cable passages are included. Specify the mounting surface and backing for the illuminated graphic; the tower's overall depth is not the available LED-to-fabric distance. Check that normal access to storage will not move cables or place stored items into the lighting cavity.
Review the tower in its intended storage configuration
Test the actual printed fabric with the proposed partition and doors installed. Review the face with storage configured as intended, and check whether partition edges or access details introduce shadows or light leakage. Record the module positions and the boundary that must stay clear. Recheck the sample if the storage layout changes, rather than relying on an empty-frame lighting test.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Does a storage-tower lightbox need a medical-device light source?
This selection concerns indoor printed booth graphics. It does not qualify modules for medical devices, treatment equipment or clinical illumination. Confirm each chosen component's voltage, connector, driver and environmental requirements for the lightbox itself.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the tower section drawing, storage partition, access-door details and fabric sample to discuss suitable lightbox component samples.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.