RetailShow covers store design, shop fittings, lighting and displays. Choose internal LED components for fixture-integrated lightboxes, then check visibility with the merchandise in place. Browse the full LED Modules range below.
Check the graphic from the customer route
Mark the intended viewing positions on the aisle plan. Assemble shelves, stocked merchandise and adjacent fixtures before reviewing the illuminated graphic. Note hidden text, reflections and shelf shadows. Moving the internal LED source cannot make a physically obstructed message visible.
Fit the lighting around the fixture section
Confirm the illuminated opening, module clearance and cable route beside shelf supports. The profile family uses a 40.7mm-wide, 17mm-high housing; its standard 32cm lead exits at the left end on the bottom side. Confirm a different exit before ordering, and trial the final section before making repeat units.
Compare LED lightbox sources
- 7W mini edge-lit bar: 200×23×16mm, DC24V, 770lm and standard 20°×60° optics; verify available mounting and removal space.
- 10W DC-plug edge-lit bar: 360×26×16mm including lens, DC24V, 1000lm ±10%, 15°×45° optics and dual-end DC sockets.
- Aluminum-profile edge-lit family: 22W/25W/32W, DC24V, 40.7×17mm housing and 14°×47° optics; specify length and wire exit.
Will a higher-wattage module solve a shelf obstruction?
No. First change the graphic placement or fixture layout so the message can be seen. Then evaluate illumination, reflections and the selected module in the revised assembly.
Before ordering
These are internal light sources, not complete retail fixtures. Disconnect power before service. Verify DC24V, load, connector pinout and polarity; confirm power and hardware separately. The featured 10W DC-plug bar permits at most 6 per run after wiring checks. Do not transfer the limit to other models.
Send the aisle plan, stocked-fixture photos, illuminated opening, frame section, cable route and quantity through our contact page for component selection.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
RetailShow covers store design, shop fittings, lighting and displays. Choose internal LED components for fixture-integrated lightboxes, then check visibility with the merchandise in place. Browse the full LED Modules range below.
Check the graphic from the customer route
Mark the intended viewing positions on the aisle plan. Assemble shelves, stocked merchandise and adjacent fixtures before reviewing the illuminated graphic. Note hidden text, reflections and shelf shadows. Moving the internal LED source cannot make a physically obstructed message visible.
Fit the lighting around the fixture section
Confirm the illuminated opening, module clearance and cable route beside shelf supports. The profile family uses a 40.7mm-wide, 17mm-high housing; its standard 32cm lead exits at the left end on the bottom side. Confirm a different exit before ordering, and trial the final section before making repeat units.
Compare LED lightbox sources
- 7W mini edge-lit bar: 200×23×16mm, DC24V, 770lm and standard 20°×60° optics; verify available mounting and removal space.
- 10W DC-plug edge-lit bar: 360×26×16mm including lens, DC24V, 1000lm ±10%, 15°×45° optics and dual-end DC sockets.
- Aluminum-profile edge-lit family: 22W/25W/32W, DC24V, 40.7×17mm housing and 14°×47° optics; specify length and wire exit.
Will a higher-wattage module solve a shelf obstruction?
No. First change the graphic placement or fixture layout so the message can be seen. Then evaluate illumination, reflections and the selected module in the revised assembly.
Before ordering
These are internal light sources, not complete retail fixtures. Disconnect power before service. Verify DC24V, load, connector pinout and polarity; confirm power and hardware separately. The featured 10W DC-plug bar permits at most 6 per run after wiring checks. Do not transfer the limit to other models.
Send the aisle plan, stocked-fixture photos, illuminated opening, frame section, cable route and quantity through our contact page for component selection.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.