Choosing LED modules for technical graphic lightboxes at Groundwater Week? Plan backlighting for printed groundwater, well-system and equipment messages. These components illuminate transmitting graphics; they do not replace working lights for machinery.
How do I keep fine diagram lines readable in a lightbox?
Test the actual printed diagram, labels and background in a working frame section. Check line contrast and light uniformity from the planned viewing distance. Compare edge lighting with rear backlighting for the measured depth; extra wattage alone cannot correct poor print contrast or bright spots.
How should I plan a lightbox beside an equipment demonstration?
Mark the printed face, demo equipment and cable routes on the booth drawing. Keep the graphic visible and connectors reachable without moving equipment. Identify the lightbox's compatible supply and connected load separately from demo equipment; a similar plug does not prove electrical compatibility.
Compare LED lightbox sources
- 7W mini edge-lit bar: DC24V, 200×23×16mm, 770lm, standard 20°×60° lens; compare for short frame sections.
- 12W dual-CCT backlight bar: DC24V, 1320lm, 180° beam, 3-wire JST. Choose the CCT pair and separate control.
- Linkable edge-lit bars: DC24V, 212mm/9W, 319mm/14W or 480mm/20W; select length for the tested frame.
Are these LEDs suitable for downhole inspection or machine work lighting?
This collection is for exhibition graphic lightboxes. It does not establish performance as a borehole camera light, inspection lamp or machine task light. Choose equipment lighting separately against its intended operating conditions.
Before ordering
For the featured models, verify DC24V, total load, connector pinout and polarity; power supplies are separate. The dual-CCT bar needs a compatible separate 3-wire switch/controller. Only the featured linkable family specifies up to five compatible bars per run, subject to circuit checks.
Send the booth and frame drawings, clear lighting depth, diagram print sample, expected reading distance and supply/connector details. Request a sample lighting check before selecting production quantities; compare the full Modules range below.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
-
7W 200mm Mini LED Light Box Bar – 770lm, DC24V -
12W Dual-CCT Switchable LED Lightbox Bar – 24V -
DC24V Linkable Edge-Lit LED Light Box Bars for SEG Displays -
12W/18W LED Module for MODULAP Fabric Lightbox -
45W High-Output Edge-Lit LED Bar for Large Light Boxes – 958mm, 4400lm -
20W Rigid LED Light Box Bars – 2200lm, DC24V, 10-Pack+ -
10W Slim Edge-Lit LED Lightbox Bar – 360mm, 9°×50° Lens -
12W Compact LED Lightbox Bar – 313mm, 24V, 6 LEDs, 1200lm -
18W LED Lightbox Bar – 585mm, 24V, 9 LEDs, 14°×50° Optical Lens -
10W DC Plug LED Lightbox Bar – 360mm, 24V, 15°×45° Optical Lens -
12W Dual-Angle LED Lightbox Bar – 517mm, 24V, 15°×45° Optical Lens -
22W–32W Aluminum Profile LED Lightbox Modules – 10-Pack+ -
10W Edge-Lit LED Light Box Bars – 360mm, 10-Pack+ -
Edge-Lit LED Module for Light Boxes – 3.5W/7W/21W, ETL Listed, DC24V -
DC Plug LED Backlight Bar for Light Boxes – 3W/6W/9W Modular System -
8W Corner LED Module, Compact Edge-Lit Light Source for SEG Fabric Light Boxes – 202mm, 10-Pack+ -
30W RGBW LED Light Bars – 400mm, 10-Pack+ -
27.5W Optical Edge-Lit LED Light Box Bars – 10-Pack+ -
14W 313mm-Long Edge-Lit LED Light Box Bars – 1540lm -
32W 4-in-1 RGBW Edge-Lit LED Light Box Bars – 10-Pack+ -
24W RGB Edge-Lit LED Bar for SEG Light Boxes & Displays -
Side-Lit LED Module for MODULAP Systems -
7W DC24V Side-Lit LED Lightbox Module – Optical Lens -
13W Edge-Lit LED Lightbox Bar – 360mm, 1430lm, ETL Listed
Choosing LED modules for technical graphic lightboxes at Groundwater Week? Plan backlighting for printed groundwater, well-system and equipment messages. These components illuminate transmitting graphics; they do not replace working lights for machinery.
How do I keep fine diagram lines readable in a lightbox?
Test the actual printed diagram, labels and background in a working frame section. Check line contrast and light uniformity from the planned viewing distance. Compare edge lighting with rear backlighting for the measured depth; extra wattage alone cannot correct poor print contrast or bright spots.
How should I plan a lightbox beside an equipment demonstration?
Mark the printed face, demo equipment and cable routes on the booth drawing. Keep the graphic visible and connectors reachable without moving equipment. Identify the lightbox's compatible supply and connected load separately from demo equipment; a similar plug does not prove electrical compatibility.
Compare LED lightbox sources
- 7W mini edge-lit bar: DC24V, 200×23×16mm, 770lm, standard 20°×60° lens; compare for short frame sections.
- 12W dual-CCT backlight bar: DC24V, 1320lm, 180° beam, 3-wire JST. Choose the CCT pair and separate control.
- Linkable edge-lit bars: DC24V, 212mm/9W, 319mm/14W or 480mm/20W; select length for the tested frame.
Are these LEDs suitable for downhole inspection or machine work lighting?
This collection is for exhibition graphic lightboxes. It does not establish performance as a borehole camera light, inspection lamp or machine task light. Choose equipment lighting separately against its intended operating conditions.
Before ordering
For the featured models, verify DC24V, total load, connector pinout and polarity; power supplies are separate. The dual-CCT bar needs a compatible separate 3-wire switch/controller. Only the featured linkable family specifies up to five compatible bars per run, subject to circuit checks.
Send the booth and frame drawings, clear lighting depth, diagram print sample, expected reading distance and supply/connector details. Request a sample lighting check before selecting production quantities; compare the full Modules range below.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.