Victory Design Open Days introduce signmaking hardware, digital print media and production demonstrations. Its own backlit-media guidance identifies lightbox and display applications. For indoor lightbox builders, this collection focuses on preparing the printed face for a useful lighting trial.
Record the print sample and its drying instructions
Label the media reference, ink process and print job. Follow the current printer, ink and media instructions for drying before applying or assembling the face. Record the sample’s condition when tested; a sample assessed at a different production stage is not a like-for-like reference.
Evaluate the prepared face in the intended lightbox
Once the print is ready for assembly, test it with the proposed LED layout and supply. Keep print preparation and lighting changes separate in the acceptance record. If either changes, review the assembled sample again rather than relying on the earlier illuminated reference.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Can a stronger LED module replace the required print-drying step?
No. LED output does not establish that printed media is ready to assemble. Follow material instructions and verify the finished combination physically. These are internal light sources for independently specified lightboxes, not printer-drying parts or replacement components approved for Victory Design’s finished displays.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Compare all LED Modules below. Send the lightbox depth, face-media reference, print process and intended supply arrangement to discuss candidates before ordering.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
-
20W Rigid LED Light Box Bars – 2200lm, DC24V, 10-Pack+ -
12W Dual-CCT Switchable LED Lightbox Bar – 24V -
10W Slim Edge-Lit LED Lightbox Bar – 360mm, 9°×50° Lens -
12W/18W LED Module for MODULAP Fabric Lightbox -
45W High-Output Edge-Lit LED Bar for Large Light Boxes – 958mm, 4400lm -
DC24V Linkable Edge-Lit LED Light Box Bars for SEG Displays -
12W Compact LED Lightbox Bar – 313mm, 24V, 6 LEDs, 1200lm -
18W LED Lightbox Bar – 585mm, 24V, 9 LEDs, 14°×50° Optical Lens -
10W DC Plug LED Lightbox Bar – 360mm, 24V, 15°×45° Optical Lens -
12W Dual-Angle LED Lightbox Bar – 517mm, 24V, 15°×45° Optical Lens -
22W–32W Aluminum Profile LED Lightbox Modules – 10-Pack+ -
10W Edge-Lit LED Light Box Bars – 360mm, 10-Pack+ -
Edge-Lit LED Module for Light Boxes – 3.5W/7W/21W, ETL Listed, DC24V -
DC Plug LED Backlight Bar for Light Boxes – 3W/6W/9W Modular System -
8W Corner LED Module, Compact Edge-Lit Light Source for SEG Fabric Light Boxes – 202mm, 10-Pack+ -
30W RGBW LED Light Bars – 400mm, 10-Pack+ -
27.5W Optical Edge-Lit LED Light Box Bars – 10-Pack+ -
14W 313mm-Long Edge-Lit LED Light Box Bars – 1540lm -
32W 4-in-1 RGBW Edge-Lit LED Light Box Bars – 10-Pack+ -
24W RGB Edge-Lit LED Bar for SEG Light Boxes & Displays -
Side-Lit LED Module for MODULAP Systems -
7W DC24V Side-Lit LED Lightbox Module – Optical Lens -
7W 200mm Mini LED Light Box Bar – 770lm, DC24V -
13W Edge-Lit LED Lightbox Bar – 360mm, 1430lm, ETL Listed
Victory Design Open Days introduce signmaking hardware, digital print media and production demonstrations. Its own backlit-media guidance identifies lightbox and display applications. For indoor lightbox builders, this collection focuses on preparing the printed face for a useful lighting trial.
Record the print sample and its drying instructions
Label the media reference, ink process and print job. Follow the current printer, ink and media instructions for drying before applying or assembling the face. Record the sample’s condition when tested; a sample assessed at a different production stage is not a like-for-like reference.
Evaluate the prepared face in the intended lightbox
Once the print is ready for assembly, test it with the proposed LED layout and supply. Keep print preparation and lighting changes separate in the acceptance record. If either changes, review the assembled sample again rather than relying on the earlier illuminated reference.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Can a stronger LED module replace the required print-drying step?
No. LED output does not establish that printed media is ready to assemble. Follow material instructions and verify the finished combination physically. These are internal light sources for independently specified lightboxes, not printer-drying parts or replacement components approved for Victory Design’s finished displays.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Compare all LED Modules below. Send the lightbox depth, face-media reference, print process and intended supply arrangement to discuss candidates before ordering.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.