Looking for LED modules for a SPACE Rennes booth lightbox divider? This selection helps stand builders plan the internal light source of a partition beside a livestock-sector meeting area, with the illuminated face and conversation space considered together.
How do I prevent shadows at the ends of a lightbox meeting divider?
Draw the illuminated face, usable depth, end returns and any opaque back panel before placing LED bars. A room-divider layout is not simply a backwall turned sideways. If the face carries a translucent print, test the actual print and assembled corners; end caps, joints or bracing can interrupt light even when the centre looks bright.
Can I shorten the divider or move it to a different stand layout?
Check the new mounting spans, optical spacing and cable route before reusing the LEDs. A shorter frame changes the illuminated geometry; removing bars also changes the electrical load. Keep connectors and the separate driver accessible from the permitted service side, without routing cables across the meeting entrance or trapping them behind furniture.
Compare LED lightbox sources
- 7W mini LED bar — DC24V, 200×23×16mm, 770lm, standard 20°×60° lens; verify end clearance and external driver.
- 20W rigid LED bar — DC24V, 470×24×16mm including lens, 2200lm ±10%, 10°×40° optics; check frame section and connector pinout.
- Linkable LED bar — DC24V; 212mm/9W, 319mm/14W or 480mm/20W; standard 20°×60° lens; verify each variant and run limit.
What should I send for a SPACE lightbox-divider component enquiry?
Send a frame section, illuminated face size, single- or double-face arrangement, end-detail drawing and print sample where used. Identify the service opening and existing power system. Confirm DC voltage, connector pinout, polarity, compatible run limit and calculated driver load for the selected variant.
Before ordering
Use a compatible separate external driver and verify the complete assembled divider. Confirm alteration permission for an existing frame. LED bars provide illumination; frame stability and meeting privacy require their own design review.
Browse all 26 LED Modules below. Send the divider drawing and intended mounting layout for a component-selection enquiry.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
-
7W 200mm Mini LED Light Box Bar – 770lm, DC24V -
20W Rigid LED Light Box Bars – 2200lm, DC24V, 10-Pack+ -
DC24V Linkable Edge-Lit LED Light Box Bars for SEG Displays -
12W/18W LED Module for MODULAP Fabric Lightbox -
45W High-Output Edge-Lit LED Bar for Large Light Boxes – 958mm, 4400lm -
Side-Lit LED Module for MODULAP Systems -
10W Slim Edge-Lit LED Lightbox Bar – 360mm, 9°×50° Lens -
12W Compact LED Lightbox Bar – 313mm, 24V, 6 LEDs, 1200lm -
18W LED Lightbox Bar – 585mm, 24V, 9 LEDs, 14°×50° Optical Lens -
10W DC Plug LED Lightbox Bar – 360mm, 24V, 15°×45° Optical Lens -
12W Dual-Angle LED Lightbox Bar – 517mm, 24V, 15°×45° Optical Lens -
22W–32W Aluminum Profile LED Lightbox Modules – 10-Pack+ -
10W Edge-Lit LED Light Box Bars – 360mm, 10-Pack+ -
Edge-Lit LED Module for Light Boxes – 3.5W/7W/21W, ETL Listed, DC24V -
DC Plug LED Backlight Bar for Light Boxes – 3W/6W/9W Modular System -
8W Corner LED Module, Compact Edge-Lit Light Source for SEG Fabric Light Boxes – 202mm, 10-Pack+ -
30W RGBW LED Light Bars – 400mm, 10-Pack+ -
27.5W Optical Edge-Lit LED Light Box Bars – 10-Pack+ -
14W 313mm-Long Edge-Lit LED Light Box Bars – 1540lm -
32W 4-in-1 RGBW Edge-Lit LED Light Box Bars – 10-Pack+ -
24W RGB Edge-Lit LED Bar for SEG Light Boxes & Displays -
7W DC24V Side-Lit LED Lightbox Module – Optical Lens -
13W Edge-Lit LED Lightbox Bar – 360mm, 1430lm, ETL Listed -
12W Dual-CCT Switchable LED Lightbox Bar – 24V
Looking for LED modules for a SPACE Rennes booth lightbox divider? This selection helps stand builders plan the internal light source of a partition beside a livestock-sector meeting area, with the illuminated face and conversation space considered together.
How do I prevent shadows at the ends of a lightbox meeting divider?
Draw the illuminated face, usable depth, end returns and any opaque back panel before placing LED bars. A room-divider layout is not simply a backwall turned sideways. If the face carries a translucent print, test the actual print and assembled corners; end caps, joints or bracing can interrupt light even when the centre looks bright.
Can I shorten the divider or move it to a different stand layout?
Check the new mounting spans, optical spacing and cable route before reusing the LEDs. A shorter frame changes the illuminated geometry; removing bars also changes the electrical load. Keep connectors and the separate driver accessible from the permitted service side, without routing cables across the meeting entrance or trapping them behind furniture.
Compare LED lightbox sources
- 7W mini LED bar — DC24V, 200×23×16mm, 770lm, standard 20°×60° lens; verify end clearance and external driver.
- 20W rigid LED bar — DC24V, 470×24×16mm including lens, 2200lm ±10%, 10°×40° optics; check frame section and connector pinout.
- Linkable LED bar — DC24V; 212mm/9W, 319mm/14W or 480mm/20W; standard 20°×60° lens; verify each variant and run limit.
What should I send for a SPACE lightbox-divider component enquiry?
Send a frame section, illuminated face size, single- or double-face arrangement, end-detail drawing and print sample where used. Identify the service opening and existing power system. Confirm DC voltage, connector pinout, polarity, compatible run limit and calculated driver load for the selected variant.
Before ordering
Use a compatible separate external driver and verify the complete assembled divider. Confirm alteration permission for an existing frame. LED bars provide illumination; frame stability and meeting privacy require their own design review.
Browse all 26 LED Modules below. Send the divider drawing and intended mounting layout for a component-selection enquiry.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.