NSSA Mid-Atlantic Sign Summit brings regional sign professionals and suppliers together. For indoor printed lightboxes, include the actual internal supports when comparing LED sources. Browse all LED Modules below for your complete frame, printed face and support arrangement.
Locate internal supports in the source drawing
Mark braces, cross-members and other opaque supports behind the visible graphic. Record their position relative to the LED bars and printed face. A source trial without these parts does not represent the final build. Keep structural parts and the approved frame configuration in the sample.
Review shadows with the complete frame assembled
After qualified mounting and wiring checks, examine the illuminated graphic with all supports installed. Record any dark band and its position against the support drawing. Discuss layout changes with the frame fabricator and retest the full sample. Do not remove or alter structural supports simply to change a shadow; the source choice alone cannot guarantee a shadow-free result.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Does an even sample without braces prove the final frame will look even?
No. Opaque internal supports may affect the illumination reaching the graphic. Review the actual supported frame, source arrangement and printed face together before approving the build.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the frame and support drawings, brace positions, printed-face material, LED candidates, observed shadow locations and quantity through our contact page.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
-
20W Rigid LED Light Box Bars – 2200lm, DC24V, 10-Pack+ -
12W Dual-CCT Switchable LED Lightbox Bar – 24V -
10W Slim Edge-Lit LED Lightbox Bar – 360mm, 9°×50° Lens -
12W/18W LED Module for MODULAP Fabric Lightbox -
45W High-Output Edge-Lit LED Bar for Large Light Boxes – 958mm, 4400lm -
DC24V Linkable Edge-Lit LED Light Box Bars for SEG Displays -
12W Compact LED Lightbox Bar – 313mm, 24V, 6 LEDs, 1200lm -
18W LED Lightbox Bar – 585mm, 24V, 9 LEDs, 14°×50° Optical Lens -
10W DC Plug LED Lightbox Bar – 360mm, 24V, 15°×45° Optical Lens -
12W Dual-Angle LED Lightbox Bar – 517mm, 24V, 15°×45° Optical Lens -
22W–32W Aluminum Profile LED Lightbox Modules – 10-Pack+ -
10W Edge-Lit LED Light Box Bars – 360mm, 10-Pack+ -
Edge-Lit LED Module for Light Boxes – 3.5W/7W/21W, ETL Listed, DC24V -
DC Plug LED Backlight Bar for Light Boxes – 3W/6W/9W Modular System -
8W Corner LED Module, Compact Edge-Lit Light Source for SEG Fabric Light Boxes – 202mm, 10-Pack+ -
30W RGBW LED Light Bars – 400mm, 10-Pack+ -
27.5W Optical Edge-Lit LED Light Box Bars – 10-Pack+ -
14W 313mm-Long Edge-Lit LED Light Box Bars – 1540lm -
32W 4-in-1 RGBW Edge-Lit LED Light Box Bars – 10-Pack+ -
24W RGB Edge-Lit LED Bar for SEG Light Boxes & Displays -
Side-Lit LED Module for MODULAP Systems -
7W DC24V Side-Lit LED Lightbox Module – Optical Lens -
7W 200mm Mini LED Light Box Bar – 770lm, DC24V -
13W Edge-Lit LED Lightbox Bar – 360mm, 1430lm, ETL Listed
NSSA Mid-Atlantic Sign Summit brings regional sign professionals and suppliers together. For indoor printed lightboxes, include the actual internal supports when comparing LED sources. Browse all LED Modules below for your complete frame, printed face and support arrangement.
Locate internal supports in the source drawing
Mark braces, cross-members and other opaque supports behind the visible graphic. Record their position relative to the LED bars and printed face. A source trial without these parts does not represent the final build. Keep structural parts and the approved frame configuration in the sample.
Review shadows with the complete frame assembled
After qualified mounting and wiring checks, examine the illuminated graphic with all supports installed. Record any dark band and its position against the support drawing. Discuss layout changes with the frame fabricator and retest the full sample. Do not remove or alter structural supports simply to change a shadow; the source choice alone cannot guarantee a shadow-free result.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Does an even sample without braces prove the final frame will look even?
No. Opaque internal supports may affect the illumination reaching the graphic. Review the actual supported frame, source arrangement and printed face together before approving the build.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the frame and support drawings, brace positions, printed-face material, LED candidates, observed shadow locations and quantity through our contact page.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.