The NRPA Annual Conference exhibits park and recreation suppliers. This selection helps independent booth-lightbox builders coordinate printed backlit graphics with nearby software demonstration screens.
Review the lightbox and demo screen together
Make a sample with the actual fabric graphic and intended LED spacing. Place the working screen in its planned position, then check both from the expected standing and seated viewing points. Identify whether bright printed areas, reflections or visible light-source patterns distract from the demonstration.
Record a repeatable display configuration
Record the selected module, driver, screen-brightness setting and print proof together. If brightness adjustment is needed, confirm a compatible control arrangement before ordering. Keep the lightbox wiring accessible for service without blocking the demo-screen cables or forcing a change to the approved lighting sample.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Does a park-sector conference make every module suitable for outdoor use?
No. This comparison is for indoor booth lightboxes, not a qualification for outdoor park installations. Review the chosen product’s environmental rating, voltage, connector and mounting requirements for the actual application; the event name does not establish suitability.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send your booth-lightbox dimensions, screen position, viewing distances and fabric proof to discuss samples and the appropriate component choice.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
-
20W Rigid LED Light Box Bars – 2200lm, DC24V, 10-Pack+ -
12W Dual-CCT Switchable LED Lightbox Bar – 24V -
10W Slim Edge-Lit LED Lightbox Bar – 360mm, 9°×50° Lens -
12W/18W LED Module for MODULAP Fabric Lightbox -
45W High-Output Edge-Lit LED Bar for Large Light Boxes – 958mm, 4400lm -
DC24V Linkable Edge-Lit LED Light Box Bars for SEG Displays -
12W Compact LED Lightbox Bar – 313mm, 24V, 6 LEDs, 1200lm -
18W LED Lightbox Bar – 585mm, 24V, 9 LEDs, 14°×50° Optical Lens -
10W DC Plug LED Lightbox Bar – 360mm, 24V, 15°×45° Optical Lens -
12W Dual-Angle LED Lightbox Bar – 517mm, 24V, 15°×45° Optical Lens -
22W–32W Aluminum Profile LED Lightbox Modules – 10-Pack+ -
10W Edge-Lit LED Light Box Bars – 360mm, 10-Pack+ -
Edge-Lit LED Module for Light Boxes – 3.5W/7W/21W, ETL Listed, DC24V -
DC Plug LED Backlight Bar for Light Boxes – 3W/6W/9W Modular System -
8W Corner LED Module, Compact Edge-Lit Light Source for SEG Fabric Light Boxes – 202mm, 10-Pack+ -
30W RGBW LED Light Bars – 400mm, 10-Pack+ -
27.5W Optical Edge-Lit LED Light Box Bars – 10-Pack+ -
14W 313mm-Long Edge-Lit LED Light Box Bars – 1540lm -
32W 4-in-1 RGBW Edge-Lit LED Light Box Bars – 10-Pack+ -
24W RGB Edge-Lit LED Bar for SEG Light Boxes & Displays -
Side-Lit LED Module for MODULAP Systems -
7W DC24V Side-Lit LED Lightbox Module – Optical Lens -
7W 200mm Mini LED Light Box Bar – 770lm, DC24V -
13W Edge-Lit LED Lightbox Bar – 360mm, 1430lm, ETL Listed
The NRPA Annual Conference exhibits park and recreation suppliers. This selection helps independent booth-lightbox builders coordinate printed backlit graphics with nearby software demonstration screens.
Review the lightbox and demo screen together
Make a sample with the actual fabric graphic and intended LED spacing. Place the working screen in its planned position, then check both from the expected standing and seated viewing points. Identify whether bright printed areas, reflections or visible light-source patterns distract from the demonstration.
Record a repeatable display configuration
Record the selected module, driver, screen-brightness setting and print proof together. If brightness adjustment is needed, confirm a compatible control arrangement before ordering. Keep the lightbox wiring accessible for service without blocking the demo-screen cables or forcing a change to the approved lighting sample.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Does a park-sector conference make every module suitable for outdoor use?
No. This comparison is for indoor booth lightboxes, not a qualification for outdoor park installations. Review the chosen product’s environmental rating, voltage, connector and mounting requirements for the actual application; the event name does not establish suitability.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send your booth-lightbox dimensions, screen position, viewing distances and fabric proof to discuss samples and the appropriate component choice.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.