Looking for NMBS Exhibition lightbox LED modules for a reusable stand wall? Compare internal LED bars using the revised illuminated opening and actual frame construction, rather than the overall booth footprint.
Can I keep the same LED bar quantity when a lightbox wall is resized?
Do not assume the previous quantity still suits the new opening. Compare the old and revised illuminated dimensions, clear depth and source mounting positions. Recalculate the selected bar layout and total load, then test the final graphic on the planned source before committing to quantities.
Should LED quantities follow the booth footprint or the illuminated panel?
Use the actual lightbox faces. A larger or smaller stand area does not establish how much of its wall is backlit. Keep ordinary product panels and door displays separate, and review each resized graphic enclosure against its own geometry and source distribution.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
What needs checking in a reused lightbox wiring harness?
Check the revised wiring route, cable condition, connector pinout, polarity and supply capacity against the chosen bars. Confirm mounting clearance and accessible connections in the reconfigured frame. A reused plug or frame does not establish electrical or optical compatibility.
Before ordering
For the three featured bars: Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Compare all LED Modules below. Send the old and revised lightbox drawings, final graphic sample and power labels to review internal bars for the resized wall.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
-
20W Rigid LED Light Box Bars – 2200lm, DC24V, 10-Pack+ -
12W Dual-CCT Switchable LED Lightbox Bar – 24V -
10W Slim Edge-Lit LED Lightbox Bar – 360mm, 9°×50° Lens -
12W/18W LED Module for MODULAP Fabric Lightbox -
45W High-Output Edge-Lit LED Bar for Large Light Boxes – 958mm, 4400lm -
DC24V Linkable Edge-Lit LED Light Box Bars for SEG Displays -
12W Compact LED Lightbox Bar – 313mm, 24V, 6 LEDs, 1200lm -
18W LED Lightbox Bar – 585mm, 24V, 9 LEDs, 14°×50° Optical Lens -
10W DC Plug LED Lightbox Bar – 360mm, 24V, 15°×45° Optical Lens -
12W Dual-Angle LED Lightbox Bar – 517mm, 24V, 15°×45° Optical Lens -
22W–32W Aluminum Profile LED Lightbox Modules – 10-Pack+ -
10W Edge-Lit LED Light Box Bars – 360mm, 10-Pack+ -
Edge-Lit LED Module for Light Boxes – 3.5W/7W/21W, ETL Listed, DC24V -
DC Plug LED Backlight Bar for Light Boxes – 3W/6W/9W Modular System -
8W Corner LED Module, Compact Edge-Lit Light Source for SEG Fabric Light Boxes – 202mm, 10-Pack+ -
30W RGBW LED Light Bars – 400mm, 10-Pack+ -
27.5W Optical Edge-Lit LED Light Box Bars – 10-Pack+ -
14W 313mm-Long Edge-Lit LED Light Box Bars – 1540lm -
32W 4-in-1 RGBW Edge-Lit LED Light Box Bars – 10-Pack+ -
24W RGB Edge-Lit LED Bar for SEG Light Boxes & Displays -
Side-Lit LED Module for MODULAP Systems -
7W DC24V Side-Lit LED Lightbox Module – Optical Lens -
7W 200mm Mini LED Light Box Bar – 770lm, DC24V -
13W Edge-Lit LED Lightbox Bar – 360mm, 1430lm, ETL Listed
Looking for NMBS Exhibition lightbox LED modules for a reusable stand wall? Compare internal LED bars using the revised illuminated opening and actual frame construction, rather than the overall booth footprint.
Can I keep the same LED bar quantity when a lightbox wall is resized?
Do not assume the previous quantity still suits the new opening. Compare the old and revised illuminated dimensions, clear depth and source mounting positions. Recalculate the selected bar layout and total load, then test the final graphic on the planned source before committing to quantities.
Should LED quantities follow the booth footprint or the illuminated panel?
Use the actual lightbox faces. A larger or smaller stand area does not establish how much of its wall is backlit. Keep ordinary product panels and door displays separate, and review each resized graphic enclosure against its own geometry and source distribution.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
What needs checking in a reused lightbox wiring harness?
Check the revised wiring route, cable condition, connector pinout, polarity and supply capacity against the chosen bars. Confirm mounting clearance and accessible connections in the reconfigured frame. A reused plug or frame does not establish electrical or optical compatibility.
Before ordering
For the three featured bars: Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Compare all LED Modules below. Send the old and revised lightbox drawings, final graphic sample and power labels to review internal bars for the resized wall.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.