Planning an independent National Restaurant Association Show booth with a printed lightbox and several demonstration stands? Compare all 26 LED Modules products for the lightbox's internal source. Map which parts of the illuminated message can be seen from each station before changing module output.
Mark an approach point for each demonstration station
Place the lightbox, monitor stands and intended operator positions on the booth plan. Mark a visitor approach point for each station and identify the logo or headline area that should be visible from there. Check those sightlines using a representative print and the planned stand heights. Do not move the lightbox message into a hidden area merely because it appears clear in an empty-booth rendering.
Record message visibility separately from the lighting proof
At each marked approach point, note which important printed areas are hidden by stands or the intended operator position. Keep this visibility map separate from the lightbox's brightness and uniformity observations. If a stand or artwork zone moves, repeat the station checks with the same accepted light source before deciding whether to change the LEDs. A brighter module cannot reveal lettering physically blocked by another display.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Do LED modules supply the monitors or the complete rental booth?
No. These are internal light sources for printed lightboxes, not monitor pixels, demo-stand hardware or complete rental packages. Establish whether the lightbox actually needs components, obtain the frame provider's agreement for changes, and verify mounting and electrical requirements independently.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the lightbox section, demo-stand plan and heights, marked visitor approach points, artwork zones and visibility observations to discuss LED options for a representative printed-lightbox trial.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
-
20W Rigid LED Light Box Bars – 2200lm, DC24V, 10-Pack+ -
12W Dual-CCT Switchable LED Lightbox Bar – 24V -
10W Slim Edge-Lit LED Lightbox Bar – 360mm, 9°×50° Lens -
12W/18W LED Module for MODULAP Fabric Lightbox -
45W High-Output Edge-Lit LED Bar for Large Light Boxes – 958mm, 4400lm -
DC24V Linkable Edge-Lit LED Light Box Bars for SEG Displays -
12W Compact LED Lightbox Bar – 313mm, 24V, 6 LEDs, 1200lm -
18W LED Lightbox Bar – 585mm, 24V, 9 LEDs, 14°×50° Optical Lens -
10W DC Plug LED Lightbox Bar – 360mm, 24V, 15°×45° Optical Lens -
12W Dual-Angle LED Lightbox Bar – 517mm, 24V, 15°×45° Optical Lens -
22W–32W Aluminum Profile LED Lightbox Modules – 10-Pack+ -
10W Edge-Lit LED Light Box Bars – 360mm, 10-Pack+ -
Edge-Lit LED Module for Light Boxes – 3.5W/7W/21W, ETL Listed, DC24V -
DC Plug LED Backlight Bar for Light Boxes – 3W/6W/9W Modular System -
8W Corner LED Module, Compact Edge-Lit Light Source for SEG Fabric Light Boxes – 202mm, 10-Pack+ -
30W RGBW LED Light Bars – 400mm, 10-Pack+ -
27.5W Optical Edge-Lit LED Light Box Bars – 10-Pack+ -
14W 313mm-Long Edge-Lit LED Light Box Bars – 1540lm -
32W 4-in-1 RGBW Edge-Lit LED Light Box Bars – 10-Pack+ -
24W RGB Edge-Lit LED Bar for SEG Light Boxes & Displays -
Side-Lit LED Module for MODULAP Systems -
7W DC24V Side-Lit LED Lightbox Module – Optical Lens -
7W 200mm Mini LED Light Box Bar – 770lm, DC24V -
13W Edge-Lit LED Lightbox Bar – 360mm, 1430lm, ETL Listed
Planning an independent National Restaurant Association Show booth with a printed lightbox and several demonstration stands? Compare all 26 LED Modules products for the lightbox's internal source. Map which parts of the illuminated message can be seen from each station before changing module output.
Mark an approach point for each demonstration station
Place the lightbox, monitor stands and intended operator positions on the booth plan. Mark a visitor approach point for each station and identify the logo or headline area that should be visible from there. Check those sightlines using a representative print and the planned stand heights. Do not move the lightbox message into a hidden area merely because it appears clear in an empty-booth rendering.
Record message visibility separately from the lighting proof
At each marked approach point, note which important printed areas are hidden by stands or the intended operator position. Keep this visibility map separate from the lightbox's brightness and uniformity observations. If a stand or artwork zone moves, repeat the station checks with the same accepted light source before deciding whether to change the LEDs. A brighter module cannot reveal lettering physically blocked by another display.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Do LED modules supply the monitors or the complete rental booth?
No. These are internal light sources for printed lightboxes, not monitor pixels, demo-stand hardware or complete rental packages. Establish whether the lightbox actually needs components, obtain the frame provider's agreement for changes, and verify mounting and electrical requirements independently.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the lightbox section, demo-stand plan and heights, marked visitor approach points, artwork zones and visibility observations to discuss LED options for a representative printed-lightbox trial.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.