IEEE PES T&D is a transmission and distribution conference and exposition. This selection supports independent exhibit builders specifying printed backlit walls around large equipment displays, with attention to the space needed to access lightbox components.
Draw the service route with the exhibit equipment in place
Include the equipment footprint, lightbox access panel and intended LED mounting positions in the booth drawing. Check where a technician would reach the connector, external driver and fastening points without moving a large display object. A module that fits inside the empty frame may still be inaccessible once the exhibit is assembled. Keep the lightbox service route distinct from equipment controls and demonstration cables.
Sample the graphic and check the proposed access sequence
Test the actual printed face with the proposed source spacing and backing. Then review the planned access sequence using the component positions and available clearances: opening the lightbox, disconnecting the correct module and reaching its fasteners. Record the accepted source layout and service approach together. Recheck both if the equipment footprint or wall access changes; do not assume a smaller module alone resolves a blocked service route.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Are these modules replacement lights for electrical demonstration equipment?
This selection concerns internal light sources for independently designed printed booth lightboxes. It does not qualify modules for transmission equipment, utility installations or demonstration machinery. Confirm the lightbox model's voltage, connector and external supply separately.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the lightbox section, equipment footprint, access-panel position and source layout to discuss suitable component samples.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
-
20W Rigid LED Light Box Bars – 2200lm, DC24V, 10-Pack+ -
12W Dual-CCT Switchable LED Lightbox Bar – 24V -
10W Slim Edge-Lit LED Lightbox Bar – 360mm, 9°×50° Lens -
12W/18W LED Module for MODULAP Fabric Lightbox -
45W High-Output Edge-Lit LED Bar for Large Light Boxes – 958mm, 4400lm -
DC24V Linkable Edge-Lit LED Light Box Bars for SEG Displays -
12W Compact LED Lightbox Bar – 313mm, 24V, 6 LEDs, 1200lm -
18W LED Lightbox Bar – 585mm, 24V, 9 LEDs, 14°×50° Optical Lens -
10W DC Plug LED Lightbox Bar – 360mm, 24V, 15°×45° Optical Lens -
12W Dual-Angle LED Lightbox Bar – 517mm, 24V, 15°×45° Optical Lens -
22W–32W Aluminum Profile LED Lightbox Modules – 10-Pack+ -
10W Edge-Lit LED Light Box Bars – 360mm, 10-Pack+ -
Edge-Lit LED Module for Light Boxes – 3.5W/7W/21W, ETL Listed, DC24V -
DC Plug LED Backlight Bar for Light Boxes – 3W/6W/9W Modular System -
8W Corner LED Module, Compact Edge-Lit Light Source for SEG Fabric Light Boxes – 202mm, 10-Pack+ -
30W RGBW LED Light Bars – 400mm, 10-Pack+ -
27.5W Optical Edge-Lit LED Light Box Bars – 10-Pack+ -
14W 313mm-Long Edge-Lit LED Light Box Bars – 1540lm -
32W 4-in-1 RGBW Edge-Lit LED Light Box Bars – 10-Pack+ -
24W RGB Edge-Lit LED Bar for SEG Light Boxes & Displays -
Side-Lit LED Module for MODULAP Systems -
7W DC24V Side-Lit LED Lightbox Module – Optical Lens -
7W 200mm Mini LED Light Box Bar – 770lm, DC24V -
13W Edge-Lit LED Lightbox Bar – 360mm, 1430lm, ETL Listed
IEEE PES T&D is a transmission and distribution conference and exposition. This selection supports independent exhibit builders specifying printed backlit walls around large equipment displays, with attention to the space needed to access lightbox components.
Draw the service route with the exhibit equipment in place
Include the equipment footprint, lightbox access panel and intended LED mounting positions in the booth drawing. Check where a technician would reach the connector, external driver and fastening points without moving a large display object. A module that fits inside the empty frame may still be inaccessible once the exhibit is assembled. Keep the lightbox service route distinct from equipment controls and demonstration cables.
Sample the graphic and check the proposed access sequence
Test the actual printed face with the proposed source spacing and backing. Then review the planned access sequence using the component positions and available clearances: opening the lightbox, disconnecting the correct module and reaching its fasteners. Record the accepted source layout and service approach together. Recheck both if the equipment footprint or wall access changes; do not assume a smaller module alone resolves a blocked service route.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Are these modules replacement lights for electrical demonstration equipment?
This selection concerns internal light sources for independently designed printed booth lightboxes. It does not qualify modules for transmission equipment, utility installations or demonstration machinery. Confirm the lightbox model's voltage, connector and external supply separately.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the lightbox section, equipment footprint, access-panel position and source layout to discuss suitable component samples.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.