Building illuminated graphics for HR Technology Conference & Exposition? Broad white panels framed by dark borders require a different sample review from dense artwork. This LED Modules selection helps exhibit fabricators compare internal lightbox components for that contrast, with the full catalog available below.
Evaluate the white field and its frame boundary together
Use the intended translucent face, printed artwork and backing in a representative lightbox section. Compare the open white area, logo area, corners and the boundary next to the dark frame under consistent viewing conditions. Record visible light-source patterns and uneven areas; a small bright logo sample alone does not represent a large white field. Adjust spacing or mounting depth and repeat the same comparison before approving the layout.
Keep the approved face sample with the component record
Record face material, print version, backing, LED model, spacing, voltage, connector and driver. If white coverage or border width changes, review the revised sample again rather than approving it from an earlier photograph. Check the selected product dimensions and electrical requirements before ordering; the catalog contains alternatives, not a claim that every model suits the same frame.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Does choosing a white-light LED guarantee a uniform white panel?
No. The visible result also depends on the face material, ink, backing, lightbox depth and source layout. Test the actual assembly. These components are for independent lightbox construction; they are not replacement parts for interactive screens or HR demonstration equipment.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send your white-panel dimensions, artwork coverage, frame depth and electrical plan for a component review. Compare the 26 LED Modules products below, then confirm the chosen model and sample result before ordering.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
-
20W Rigid LED Light Box Bars – 2200lm, DC24V, 10-Pack+ -
12W Dual-CCT Switchable LED Lightbox Bar – 24V -
10W Slim Edge-Lit LED Lightbox Bar – 360mm, 9°×50° Lens -
12W/18W LED Module for MODULAP Fabric Lightbox -
45W High-Output Edge-Lit LED Bar for Large Light Boxes – 958mm, 4400lm -
DC24V Linkable Edge-Lit LED Light Box Bars for SEG Displays -
12W Compact LED Lightbox Bar – 313mm, 24V, 6 LEDs, 1200lm -
18W LED Lightbox Bar – 585mm, 24V, 9 LEDs, 14°×50° Optical Lens -
10W DC Plug LED Lightbox Bar – 360mm, 24V, 15°×45° Optical Lens -
12W Dual-Angle LED Lightbox Bar – 517mm, 24V, 15°×45° Optical Lens -
22W–32W Aluminum Profile LED Lightbox Modules – 10-Pack+ -
10W Edge-Lit LED Light Box Bars – 360mm, 10-Pack+ -
Edge-Lit LED Module for Light Boxes – 3.5W/7W/21W, ETL Listed, DC24V -
DC Plug LED Backlight Bar for Light Boxes – 3W/6W/9W Modular System -
8W Corner LED Module, Compact Edge-Lit Light Source for SEG Fabric Light Boxes – 202mm, 10-Pack+ -
30W RGBW LED Light Bars – 400mm, 10-Pack+ -
27.5W Optical Edge-Lit LED Light Box Bars – 10-Pack+ -
14W 313mm-Long Edge-Lit LED Light Box Bars – 1540lm -
32W 4-in-1 RGBW Edge-Lit LED Light Box Bars – 10-Pack+ -
24W RGB Edge-Lit LED Bar for SEG Light Boxes & Displays -
Side-Lit LED Module for MODULAP Systems -
7W DC24V Side-Lit LED Lightbox Module – Optical Lens -
7W 200mm Mini LED Light Box Bar – 770lm, DC24V -
13W Edge-Lit LED Lightbox Bar – 360mm, 1430lm, ETL Listed
Building illuminated graphics for HR Technology Conference & Exposition? Broad white panels framed by dark borders require a different sample review from dense artwork. This LED Modules selection helps exhibit fabricators compare internal lightbox components for that contrast, with the full catalog available below.
Evaluate the white field and its frame boundary together
Use the intended translucent face, printed artwork and backing in a representative lightbox section. Compare the open white area, logo area, corners and the boundary next to the dark frame under consistent viewing conditions. Record visible light-source patterns and uneven areas; a small bright logo sample alone does not represent a large white field. Adjust spacing or mounting depth and repeat the same comparison before approving the layout.
Keep the approved face sample with the component record
Record face material, print version, backing, LED model, spacing, voltage, connector and driver. If white coverage or border width changes, review the revised sample again rather than approving it from an earlier photograph. Check the selected product dimensions and electrical requirements before ordering; the catalog contains alternatives, not a claim that every model suits the same frame.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Does choosing a white-light LED guarantee a uniform white panel?
No. The visible result also depends on the face material, ink, backing, lightbox depth and source layout. Test the actual assembly. These components are for independent lightbox construction; they are not replacement parts for interactive screens or HR demonstration equipment.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send your white-panel dimensions, artwork coverage, frame depth and electrical plan for a component review. Compare the 26 LED Modules products below, then confirm the chosen model and sample result before ordering.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.