Updating a CPMA produce-show stand while retaining parts of an existing display? Compare all 26 LED Modules products for an independently built graphic lightbox. Keep the retained hardware specification separate from the new-source proposal.
Inventory retained and added lightbox components
Mark which frame sections, LEDs, drivers and harnesses are retained, newly purchased or rented. Record their actual labels, voltage, connector pin arrangement and mounting interfaces. An older frame being reusable does not establish that its LED bars or driver can run a new lightbox section.
Resolve the interface before mixing components
Ask the builder to identify exactly which existing components the proposed LED layout uses. Keep unsupported combinations out of the trial, and confirm rental modification conditions with the equipment owner. Review a sample containing the intended retained and new sections, using their proposed power supplies and prints. Record what was actually evaluated so the production order does not silently substitute another source or harness.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Does a familiar connector make old and new modules interchangeable?
No. A similar connector shape does not prove matching pin assignments, voltage, current requirements or mounting. This selection is for indoor graphic lightboxes, not produce-growing lamps or refrigeration lighting.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the retained-component inventory, frame drawings, proposed new sections and electrical interfaces for an LED module comparison.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
-
20W Rigid LED Light Box Bars – 2200lm, DC24V, 10-Pack+ -
12W Dual-CCT Switchable LED Lightbox Bar – 24V -
10W Slim Edge-Lit LED Lightbox Bar – 360mm, 9°×50° Lens -
12W/18W LED Module for MODULAP Fabric Lightbox -
45W High-Output Edge-Lit LED Bar for Large Light Boxes – 958mm, 4400lm -
DC24V Linkable Edge-Lit LED Light Box Bars for SEG Displays -
12W Compact LED Lightbox Bar – 313mm, 24V, 6 LEDs, 1200lm -
18W LED Lightbox Bar – 585mm, 24V, 9 LEDs, 14°×50° Optical Lens -
10W DC Plug LED Lightbox Bar – 360mm, 24V, 15°×45° Optical Lens -
12W Dual-Angle LED Lightbox Bar – 517mm, 24V, 15°×45° Optical Lens -
22W–32W Aluminum Profile LED Lightbox Modules – 10-Pack+ -
10W Edge-Lit LED Light Box Bars – 360mm, 10-Pack+ -
Edge-Lit LED Module for Light Boxes – 3.5W/7W/21W, ETL Listed, DC24V -
DC Plug LED Backlight Bar for Light Boxes – 3W/6W/9W Modular System -
8W Corner LED Module, Compact Edge-Lit Light Source for SEG Fabric Light Boxes – 202mm, 10-Pack+ -
30W RGBW LED Light Bars – 400mm, 10-Pack+ -
27.5W Optical Edge-Lit LED Light Box Bars – 10-Pack+ -
14W 313mm-Long Edge-Lit LED Light Box Bars – 1540lm -
32W 4-in-1 RGBW Edge-Lit LED Light Box Bars – 10-Pack+ -
24W RGB Edge-Lit LED Bar for SEG Light Boxes & Displays -
Side-Lit LED Module for MODULAP Systems -
7W DC24V Side-Lit LED Lightbox Module – Optical Lens -
7W 200mm Mini LED Light Box Bar – 770lm, DC24V -
13W Edge-Lit LED Lightbox Bar – 360mm, 1430lm, ETL Listed
Updating a CPMA produce-show stand while retaining parts of an existing display? Compare all 26 LED Modules products for an independently built graphic lightbox. Keep the retained hardware specification separate from the new-source proposal.
Inventory retained and added lightbox components
Mark which frame sections, LEDs, drivers and harnesses are retained, newly purchased or rented. Record their actual labels, voltage, connector pin arrangement and mounting interfaces. An older frame being reusable does not establish that its LED bars or driver can run a new lightbox section.
Resolve the interface before mixing components
Ask the builder to identify exactly which existing components the proposed LED layout uses. Keep unsupported combinations out of the trial, and confirm rental modification conditions with the equipment owner. Review a sample containing the intended retained and new sections, using their proposed power supplies and prints. Record what was actually evaluated so the production order does not silently substitute another source or harness.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Does a familiar connector make old and new modules interchangeable?
No. A similar connector shape does not prove matching pin assignments, voltage, current requirements or mounting. This selection is for indoor graphic lightboxes, not produce-growing lamps or refrigeration lighting.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the retained-component inventory, frame drawings, proposed new sections and electrical interfaces for an LED module comparison.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.