Bangkok Ad & Sign Expo brings together signage, LED component and lightbox suppliers in Thailand. For an indoor printed lightbox fitted into a recess, compare the installation opening with the frame used for your workshop trial. Browse the full LED Modules range below.
Compare the recess with the tested frame section
Record the measured recess opening, usable depth, frame back, intended cable exit and nearby obstructions. Mark which dimensions changed since the bench sample. Confirm space for the chosen bar, lens, connector and mounting parts using their actual dimensions; the nominal recess depth is not the usable optical depth.
Check how components leave the installed frame
Before approving the component order, draw the service opening and removal path for the selected source and its mating cable. Account for fixings and adjacent finishes that may restrict access. After qualified assembly and wiring checks, review the actual printed face in the installed configuration. Recess fit does not establish electrical compliance or prove the same illumination as an unobstructed bench sample.
Compare LED lightbox sources
- 7W mini edge-lit bar: 200×23×16mm, DC24V, 770lm and standard 20°×60° optics; verify available mounting and removal space.
- 10W DC-plug edge-lit bar: 360×26×16mm including lens, DC24V, 1000lm ±10%, 15°×45° optics and dual-end DC sockets.
- Aluminum-profile edge-lit family: 22W/25W/32W, DC24V, 40.7×17mm housing and 14°×47° optics; specify length and wire exit.
Can a successful bench sample approve a recessed installation?
No. Installation boundaries can alter available depth, cable access and removal space. Compare the recess with the trial assembly and test the intended configuration before accepting the LED arrangement.
Before ordering
These are internal light sources, not complete retail fixtures. Disconnect power before service. Verify DC24V, load, connector pinout and polarity; confirm power and hardware separately. The featured 10W DC-plug bar permits at most 6 per run after wiring checks. Do not transfer the limit to other models.
Send the measured recess, tested frame section, changes from the sample, service-opening drawing, source models and quantity through our contact page.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
-
7W 200mm Mini LED Light Box Bar – 770lm, DC24V -
10W DC Plug LED Lightbox Bar – 360mm, 24V, 15°×45° Optical Lens -
22W–32W Aluminum Profile LED Lightbox Modules – 10-Pack+ -
12W/18W LED Module for MODULAP Fabric Lightbox -
45W High-Output Edge-Lit LED Bar for Large Light Boxes – 958mm, 4400lm -
DC24V Linkable Edge-Lit LED Light Box Bars for SEG Displays -
20W Rigid LED Light Box Bars – 2200lm, DC24V, 10-Pack+ -
10W Slim Edge-Lit LED Lightbox Bar – 360mm, 9°×50° Lens -
12W Compact LED Lightbox Bar – 313mm, 24V, 6 LEDs, 1200lm -
18W LED Lightbox Bar – 585mm, 24V, 9 LEDs, 14°×50° Optical Lens -
12W Dual-Angle LED Lightbox Bar – 517mm, 24V, 15°×45° Optical Lens -
10W Edge-Lit LED Light Box Bars – 360mm, 10-Pack+ -
Edge-Lit LED Module for Light Boxes – 3.5W/7W/21W, ETL Listed, DC24V -
DC Plug LED Backlight Bar for Light Boxes – 3W/6W/9W Modular System -
8W Corner LED Module, Compact Edge-Lit Light Source for SEG Fabric Light Boxes – 202mm, 10-Pack+ -
30W RGBW LED Light Bars – 400mm, 10-Pack+ -
27.5W Optical Edge-Lit LED Light Box Bars – 10-Pack+ -
14W 313mm-Long Edge-Lit LED Light Box Bars – 1540lm -
32W 4-in-1 RGBW Edge-Lit LED Light Box Bars – 10-Pack+ -
24W RGB Edge-Lit LED Bar for SEG Light Boxes & Displays -
Side-Lit LED Module for MODULAP Systems -
7W DC24V Side-Lit LED Lightbox Module – Optical Lens -
13W Edge-Lit LED Lightbox Bar – 360mm, 1430lm, ETL Listed -
12W Dual-CCT Switchable LED Lightbox Bar – 24V
Bangkok Ad & Sign Expo brings together signage, LED component and lightbox suppliers in Thailand. For an indoor printed lightbox fitted into a recess, compare the installation opening with the frame used for your workshop trial. Browse the full LED Modules range below.
Compare the recess with the tested frame section
Record the measured recess opening, usable depth, frame back, intended cable exit and nearby obstructions. Mark which dimensions changed since the bench sample. Confirm space for the chosen bar, lens, connector and mounting parts using their actual dimensions; the nominal recess depth is not the usable optical depth.
Check how components leave the installed frame
Before approving the component order, draw the service opening and removal path for the selected source and its mating cable. Account for fixings and adjacent finishes that may restrict access. After qualified assembly and wiring checks, review the actual printed face in the installed configuration. Recess fit does not establish electrical compliance or prove the same illumination as an unobstructed bench sample.
Compare LED lightbox sources
- 7W mini edge-lit bar: 200×23×16mm, DC24V, 770lm and standard 20°×60° optics; verify available mounting and removal space.
- 10W DC-plug edge-lit bar: 360×26×16mm including lens, DC24V, 1000lm ±10%, 15°×45° optics and dual-end DC sockets.
- Aluminum-profile edge-lit family: 22W/25W/32W, DC24V, 40.7×17mm housing and 14°×47° optics; specify length and wire exit.
Can a successful bench sample approve a recessed installation?
No. Installation boundaries can alter available depth, cable access and removal space. Compare the recess with the trial assembly and test the intended configuration before accepting the LED arrangement.
Before ordering
These are internal light sources, not complete retail fixtures. Disconnect power before service. Verify DC24V, load, connector pinout and polarity; confirm power and hardware separately. The featured 10W DC-plug bar permits at most 6 per run after wiring checks. Do not transfer the limit to other models.
Send the measured recess, tested frame section, changes from the sample, service-opening drawing, source models and quantity through our contact page.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.