Looking for AAP Annual Meeting LED modules for a long double-sided fabric lightbox? Compare internal bars using both final printed faces, the actual enclosure depth and the planned source arrangement.
Can both fabric faces use the same LED arrangement?
Do not assume that lighting one face proves the other will look right. Check the source position relative to each front, reflective surfaces, internal obstructions and graphic transmission. Test both final prints together before fixing the layout, especially where the source arrangement serves opposing faces.
How do I check uniform lighting along a long fabric wall?
Inspect the full illuminated length, including ends, joins and areas near internal supports. Use the actual depth, source spacing and final printed fabric for the test. Shelves, monitor counters and the overall booth footprint do not define the lightbox opening or prove an even result.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Can I extend one LED run across the whole wall?
Only within the chosen model’s documented limits and the verified wiring design. Calculate each run’s load, cable size and voltage drop, and confirm supply capacity, connector pinout and polarity. Keep service access and check permission for rental-frame changes. These are graphic-lightbox components, not dental equipment or a complete display.
Before ordering
For the three featured bars: Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Compare all LED Modules below. Send samples of both fabric faces, the actual wall section and power labels to review optics, quantities and permitted electrical runs.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
-
20W Rigid LED Light Box Bars – 2200lm, DC24V, 10-Pack+ -
12W Dual-CCT Switchable LED Lightbox Bar – 24V -
10W Slim Edge-Lit LED Lightbox Bar – 360mm, 9°×50° Lens -
12W/18W LED Module for MODULAP Fabric Lightbox -
45W High-Output Edge-Lit LED Bar for Large Light Boxes – 958mm, 4400lm -
DC24V Linkable Edge-Lit LED Light Box Bars for SEG Displays -
12W Compact LED Lightbox Bar – 313mm, 24V, 6 LEDs, 1200lm -
18W LED Lightbox Bar – 585mm, 24V, 9 LEDs, 14°×50° Optical Lens -
10W DC Plug LED Lightbox Bar – 360mm, 24V, 15°×45° Optical Lens -
12W Dual-Angle LED Lightbox Bar – 517mm, 24V, 15°×45° Optical Lens -
22W–32W Aluminum Profile LED Lightbox Modules – 10-Pack+ -
10W Edge-Lit LED Light Box Bars – 360mm, 10-Pack+ -
Edge-Lit LED Module for Light Boxes – 3.5W/7W/21W, ETL Listed, DC24V -
DC Plug LED Backlight Bar for Light Boxes – 3W/6W/9W Modular System -
8W Corner LED Module, Compact Edge-Lit Light Source for SEG Fabric Light Boxes – 202mm, 10-Pack+ -
30W RGBW LED Light Bars – 400mm, 10-Pack+ -
27.5W Optical Edge-Lit LED Light Box Bars – 10-Pack+ -
14W 313mm-Long Edge-Lit LED Light Box Bars – 1540lm -
32W 4-in-1 RGBW Edge-Lit LED Light Box Bars – 10-Pack+ -
24W RGB Edge-Lit LED Bar for SEG Light Boxes & Displays -
Side-Lit LED Module for MODULAP Systems -
7W DC24V Side-Lit LED Lightbox Module – Optical Lens -
7W 200mm Mini LED Light Box Bar – 770lm, DC24V -
13W Edge-Lit LED Lightbox Bar – 360mm, 1430lm, ETL Listed
Looking for AAP Annual Meeting LED modules for a long double-sided fabric lightbox? Compare internal bars using both final printed faces, the actual enclosure depth and the planned source arrangement.
Can both fabric faces use the same LED arrangement?
Do not assume that lighting one face proves the other will look right. Check the source position relative to each front, reflective surfaces, internal obstructions and graphic transmission. Test both final prints together before fixing the layout, especially where the source arrangement serves opposing faces.
How do I check uniform lighting along a long fabric wall?
Inspect the full illuminated length, including ends, joins and areas near internal supports. Use the actual depth, source spacing and final printed fabric for the test. Shelves, monitor counters and the overall booth footprint do not define the lightbox opening or prove an even result.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Can I extend one LED run across the whole wall?
Only within the chosen model’s documented limits and the verified wiring design. Calculate each run’s load, cable size and voltage drop, and confirm supply capacity, connector pinout and polarity. Keep service access and check permission for rental-frame changes. These are graphic-lightbox components, not dental equipment or a complete display.
Before ordering
For the three featured bars: Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Compare all LED Modules below. Send samples of both fabric faces, the actual wall section and power labels to review optics, quantities and permitted electrical runs.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.