Looking for AAD Annual Meeting lightbox LED modules or replacement LED bars for existing exhibition graphics? Compare internal sources for compatible indoor printed lightboxes using the existing frame and electrical specifications.
Which LED modules can replace an existing lightbox source?
Compare source length, optics, mounts, lit dimensions and usable depth with the actual print sample. Test a proposed edge-lit or backlit arrangement before ordering; a different LED bar does not automatically fit the existing frame or deliver the same graphic appearance.
Can I reuse the old lightbox power supply?
Check the supply label, output voltage, available load capacity, connector and wiring against the selected source. Do not infer compatibility from an old lightbox’s appearance. Confirm the complete source layout and supply requirements rather than copying the old component count.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
What existing-frame details should I send?
Send print samples, lit dimensions, clear depth, mounting spans, existing-source and supply labels, connector photos and wiring layout. Confirm positions, total load and service access before ordering. These modules are graphic-lightbox sources, not medical treatment lighting or a complete lightbox.
Before ordering
For the three featured bars: Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Compare all LED Modules below. Send the existing lightbox specification to review compatible replacement sources before purchasing.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
-
20W Rigid LED Light Box Bars – 2200lm, DC24V, 10-Pack+ -
12W Dual-CCT Switchable LED Lightbox Bar – 24V -
10W Slim Edge-Lit LED Lightbox Bar – 360mm, 9°×50° Lens -
12W/18W LED Module for MODULAP Fabric Lightbox -
45W High-Output Edge-Lit LED Bar for Large Light Boxes – 958mm, 4400lm -
DC24V Linkable Edge-Lit LED Light Box Bars for SEG Displays -
12W Compact LED Lightbox Bar – 313mm, 24V, 6 LEDs, 1200lm -
18W LED Lightbox Bar – 585mm, 24V, 9 LEDs, 14°×50° Optical Lens -
10W DC Plug LED Lightbox Bar – 360mm, 24V, 15°×45° Optical Lens -
12W Dual-Angle LED Lightbox Bar – 517mm, 24V, 15°×45° Optical Lens -
22W–32W Aluminum Profile LED Lightbox Modules – 10-Pack+ -
10W Edge-Lit LED Light Box Bars – 360mm, 10-Pack+ -
Edge-Lit LED Module for Light Boxes – 3.5W/7W/21W, ETL Listed, DC24V -
DC Plug LED Backlight Bar for Light Boxes – 3W/6W/9W Modular System -
8W Corner LED Module, Compact Edge-Lit Light Source for SEG Fabric Light Boxes – 202mm, 10-Pack+ -
30W RGBW LED Light Bars – 400mm, 10-Pack+ -
27.5W Optical Edge-Lit LED Light Box Bars – 10-Pack+ -
14W 313mm-Long Edge-Lit LED Light Box Bars – 1540lm -
32W 4-in-1 RGBW Edge-Lit LED Light Box Bars – 10-Pack+ -
24W RGB Edge-Lit LED Bar for SEG Light Boxes & Displays -
Side-Lit LED Module for MODULAP Systems -
7W DC24V Side-Lit LED Lightbox Module – Optical Lens -
7W 200mm Mini LED Light Box Bar – 770lm, DC24V -
13W Edge-Lit LED Lightbox Bar – 360mm, 1430lm, ETL Listed
Looking for AAD Annual Meeting lightbox LED modules or replacement LED bars for existing exhibition graphics? Compare internal sources for compatible indoor printed lightboxes using the existing frame and electrical specifications.
Which LED modules can replace an existing lightbox source?
Compare source length, optics, mounts, lit dimensions and usable depth with the actual print sample. Test a proposed edge-lit or backlit arrangement before ordering; a different LED bar does not automatically fit the existing frame or deliver the same graphic appearance.
Can I reuse the old lightbox power supply?
Check the supply label, output voltage, available load capacity, connector and wiring against the selected source. Do not infer compatibility from an old lightbox’s appearance. Confirm the complete source layout and supply requirements rather than copying the old component count.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
What existing-frame details should I send?
Send print samples, lit dimensions, clear depth, mounting spans, existing-source and supply labels, connector photos and wiring layout. Confirm positions, total load and service access before ordering. These modules are graphic-lightbox sources, not medical treatment lighting or a complete lightbox.
Before ordering
For the three featured bars: Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Compare all LED Modules below. Send the existing lightbox specification to review compatible replacement sources before purchasing.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.