Searching for SALTEX lightbox LED modules or LED bars for SEG fabric exhibition graphics? Compare internal sources for printed turf-system diagrams and brand graphics in indoor stand lightboxes.
Which LEDs suit a SEG fabric exhibition lightbox?
Compare edge-lit and rear-backlight options with the actual fabric, usable frame depth and internal supports. Test the final print with its silicone edges seated and its tension checked before approving source spacing.
Should I fix fabric wrinkles by adding more LEDs?
No. First check the fit of the graphic, edge seating and fabric tension. Recheck the illuminated face after correcting wrinkles or sag, then inspect any remaining unwanted lighting gaps. More source power does not correct a poorly fitted fabric face.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
What frame and printed-fabric details should I send?
Send final fabric graphic, visible dimensions, frame sections and depth, edge and tension details, supports and mounting, plus connectors, supply and service access. These modules are internal sources for exhibit graphics, not turf-growing lights or outdoor equipment lamps.
Before ordering
For the three featured bars: Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Browse all LED Modules below. Send your SEG frame and finished-fabric details to compare a suitable internal source layout.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
Searching for SALTEX lightbox LED modules or LED bars for SEG fabric exhibition graphics? Compare internal sources for printed turf-system diagrams and brand graphics in indoor stand lightboxes.
Which LEDs suit a SEG fabric exhibition lightbox?
Compare edge-lit and rear-backlight options with the actual fabric, usable frame depth and internal supports. Test the final print with its silicone edges seated and its tension checked before approving source spacing.
Should I fix fabric wrinkles by adding more LEDs?
No. First check the fit of the graphic, edge seating and fabric tension. Recheck the illuminated face after correcting wrinkles or sag, then inspect any remaining unwanted lighting gaps. More source power does not correct a poorly fitted fabric face.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
What frame and printed-fabric details should I send?
Send final fabric graphic, visible dimensions, frame sections and depth, edge and tension details, supports and mounting, plus connectors, supply and service access. These modules are internal sources for exhibit graphics, not turf-growing lights or outdoor equipment lamps.
Before ordering
For the three featured bars: Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Browse all LED Modules below. Send your SEG frame and finished-fabric details to compare a suitable internal source layout.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.