Preparing a printed lightbox beside a visitor activity at NACDS Total Store Expo? This selection supports independent exhibit builders comparing all 26 LED Modules products. Focus on the internal lighting installation and the exposed cable route where visitors handle game pieces, promotional materials or demonstration fixtures.
Map the activity's handling area before routing the lightbox cable
Show the lightbox, activity fixture and intended visitor position on the same plan. Mark where hands, loose items and removable activity parts travel. Route the lightbox's external supply cable away from this handling area and provide the enclosure or protection specified by the booth designer. Keep game supports and activity attachments independent of LED bars and connectors. Check the complete connector and cable envelope, not just the module body, when selecting the internal mounting position.
Operate the activity with the finished lightbox in place
Fit the printed graphic and close the lightbox, then run the intended activity beside it. Check whether moving fixtures or loose items can pull, press or rub the lighting cable. Confirm that routine replenishment of game pieces or promotional materials does not require disturbing the LED connection. Record the accepted cable route and protection with the component list. Repeat the trial when the activity layout changes; a bare lightbox bench test does not reproduce this installation.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Does choosing an LED module qualify the interactive booth installation?
No. These are internal lightbox components, not game hardware, protective cable enclosures or complete display packages. Check mounting, power-supply and booth requirements separately. Their use in a pharmacy-industry exhibit does not qualify them for clinical or medical-device lighting.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the lightbox section, activity layout, visitor handling area, cable route and printed sample to discuss component options for an assembled-booth trial.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
Preparing a printed lightbox beside a visitor activity at NACDS Total Store Expo? This selection supports independent exhibit builders comparing all 26 LED Modules products. Focus on the internal lighting installation and the exposed cable route where visitors handle game pieces, promotional materials or demonstration fixtures.
Map the activity's handling area before routing the lightbox cable
Show the lightbox, activity fixture and intended visitor position on the same plan. Mark where hands, loose items and removable activity parts travel. Route the lightbox's external supply cable away from this handling area and provide the enclosure or protection specified by the booth designer. Keep game supports and activity attachments independent of LED bars and connectors. Check the complete connector and cable envelope, not just the module body, when selecting the internal mounting position.
Operate the activity with the finished lightbox in place
Fit the printed graphic and close the lightbox, then run the intended activity beside it. Check whether moving fixtures or loose items can pull, press or rub the lighting cable. Confirm that routine replenishment of game pieces or promotional materials does not require disturbing the LED connection. Record the accepted cable route and protection with the component list. Repeat the trial when the activity layout changes; a bare lightbox bench test does not reproduce this installation.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Does choosing an LED module qualify the interactive booth installation?
No. These are internal lightbox components, not game hardware, protective cable enclosures or complete display packages. Check mounting, power-supply and booth requirements separately. Their use in a pharmacy-industry exhibit does not qualify them for clinical or medical-device lighting.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the lightbox section, activity layout, visitor handling area, cable route and printed sample to discuss component options for an assembled-booth trial.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.