Building an independent London Packaging Week stand with a printed brand lightbox? Compare all 26 LED Modules products for its internal light source. Plan how the illuminated message will appear in publicity photos as well as to visitors.
Choose the message that must survive the photograph
Mark the logo and headline areas required in the intended stand photograph. Test the actual print and proposed LED layout from the planned camera position and framing. Review whether those areas retain readable detail instead of becoming featureless bright shapes. Keep the camera position and print fixed when comparing sources; record any exposure or control change separately.
Keep visitor approval and photo approval together
Retain an image showing the required message and a separate record of the graphic viewed by eye. If the photographic composition or source setting changes, review both again. If one arrangement cannot satisfy both uses, agree a separate photo setting or composition before ordering; verify any brightness control with the exact driver and module. An edited photograph does not approve the live illuminated face.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Does a brighter module automatically make a better stand photo?
No. Camera exposure and framing also determine which printed details remain visible. These are internal lightbox sources, with no promised camera performance or built-in dimming. Test the complete proposed configuration.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the lightbox section, final artwork, required photo message, camera position and approved viewing records to discuss a component sample.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
Building an independent London Packaging Week stand with a printed brand lightbox? Compare all 26 LED Modules products for its internal light source. Plan how the illuminated message will appear in publicity photos as well as to visitors.
Choose the message that must survive the photograph
Mark the logo and headline areas required in the intended stand photograph. Test the actual print and proposed LED layout from the planned camera position and framing. Review whether those areas retain readable detail instead of becoming featureless bright shapes. Keep the camera position and print fixed when comparing sources; record any exposure or control change separately.
Keep visitor approval and photo approval together
Retain an image showing the required message and a separate record of the graphic viewed by eye. If the photographic composition or source setting changes, review both again. If one arrangement cannot satisfy both uses, agree a separate photo setting or composition before ordering; verify any brightness control with the exact driver and module. An edited photograph does not approve the live illuminated face.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Does a brighter module automatically make a better stand photo?
No. Camera exposure and framing also determine which printed details remain visible. These are internal lightbox sources, with no promised camera performance or built-in dimming. Test the complete proposed configuration.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the lightbox section, final artwork, required photo message, camera position and approved viewing records to discuss a component sample.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.