ISOframe offers self-build training, including for Lumen lightbox customers. This independent selection focuses on packing and inspecting your own reusable indoor-lightbox components.
Plan disconnect points before closing the transport case
For your own frame design, identify which cables stay attached and which connectors must be unplugged. With power disconnected, photograph the cable route and label matching ends. Protect bars and connector bodies from being trapped beneath frame parts; do not pull on wires when disconnecting.
Inspect the light source after transport, before reassembly
Check for bent mounting parts, pinched leads and damaged connector housings before applying power. Reassemble a sample using the approved cable layout and compare illumination with the reference image. Quarantine damaged components instead of forcing a connector or changing polarity to make it fit.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Are these modules original replacement parts for ISOframe Lumen?
No original-part or Lumen compatibility claim is made. Lumen has an integrated lighting system; ask its supplier about authorised service parts. BOOTH LIGHTS module selection requires a separate review of your own frame, voltage, connector and mounting design.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send your independent lightbox dimensions, packing layout, connector photos and assembly drawing to discuss a sample and spare-component plan.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
ISOframe offers self-build training, including for Lumen lightbox customers. This independent selection focuses on packing and inspecting your own reusable indoor-lightbox components.
Plan disconnect points before closing the transport case
For your own frame design, identify which cables stay attached and which connectors must be unplugged. With power disconnected, photograph the cable route and label matching ends. Protect bars and connector bodies from being trapped beneath frame parts; do not pull on wires when disconnecting.
Inspect the light source after transport, before reassembly
Check for bent mounting parts, pinched leads and damaged connector housings before applying power. Reassemble a sample using the approved cable layout and compare illumination with the reference image. Quarantine damaged components instead of forcing a connector or changing polarity to make it fit.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Are these modules original replacement parts for ISOframe Lumen?
No original-part or Lumen compatibility claim is made. Lumen has an integrated lighting system; ask its supplier about authorised service parts. BOOTH LIGHTS module selection requires a separate review of your own frame, voltage, connector and mounting design.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send your independent lightbox dimensions, packing layout, connector photos and assembly drawing to discuss a sample and spare-component plan.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.