Preparing an illuminated product wall for interpack? Packaging-film exhibits can place branded backlit panels alongside illuminated material samples. Compare internal LED components for the wall construction while keeping the sample-viewing task distinct from ordinary graphic illumination. All 26 LED Modules products are available for comparison below.
Separate the graphic panel from the material sample
Label each wall section as printed branding or material viewing before selecting its LED layout. Keep a representative reference section with the intended backing and mounting depth. For a film-sample section, compare the same material under the same setup and record visible bands or source patterns; do not interpret a brighter panel as proof of better film quality. This selection does not establish a calibrated optical inspection system.
Preserve the comparison when changing wall sections
Record the LED model, spacing, voltage, connector, driver, backing and sample position for each section. When replacing a bar or changing a niche, compare it against the retained reference section before accepting the result. A long wall and a shallow sample recess may require different layouts. Confirm product dimensions and ratings individually rather than applying one model or chain limit to the entire catalog.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Can one LED layout serve the branded wall and every film sample?
Only after the actual sections have been evaluated for their respective purposes. Sample transmission and the printed graphic face can differ. These products are lightbox components, not certified laboratory inspection equipment, packaging-machine lighting or a complete suspended structure.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the wall-section drawings, sample materials, graphic face, usable depth and electrical plan for a component review. Compare the 26 products below and retain the approved reference setup for later replacements.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
Preparing an illuminated product wall for interpack? Packaging-film exhibits can place branded backlit panels alongside illuminated material samples. Compare internal LED components for the wall construction while keeping the sample-viewing task distinct from ordinary graphic illumination. All 26 LED Modules products are available for comparison below.
Separate the graphic panel from the material sample
Label each wall section as printed branding or material viewing before selecting its LED layout. Keep a representative reference section with the intended backing and mounting depth. For a film-sample section, compare the same material under the same setup and record visible bands or source patterns; do not interpret a brighter panel as proof of better film quality. This selection does not establish a calibrated optical inspection system.
Preserve the comparison when changing wall sections
Record the LED model, spacing, voltage, connector, driver, backing and sample position for each section. When replacing a bar or changing a niche, compare it against the retained reference section before accepting the result. A long wall and a shallow sample recess may require different layouts. Confirm product dimensions and ratings individually rather than applying one model or chain limit to the entire catalog.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Can one LED layout serve the branded wall and every film sample?
Only after the actual sections have been evaluated for their respective purposes. Sample transmission and the printed graphic face can differ. These products are lightbox components, not certified laboratory inspection equipment, packaging-machine lighting or a complete suspended structure.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the wall-section drawings, sample materials, graphic face, usable depth and electrical plan for a component review. Compare the 26 products below and retain the approved reference setup for later replacements.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.