EM Plastic serves Canada’s sign and display industry and hosts supplier open houses. For lightbox builders comparing internal LED components around these activities, this selection focuses on an unpowered connector sample board: a practical record of the connections being considered before ordering bars and harness parts.
Compare connector samples without applying power
Attach clearly identified loose connector samples or photographs to a comparison board. Record the supplier part reference, housing shape, latch position and mating direction. Keep the board unpowered and separate from a working circuit. Similar-looking connectors are comparison candidates, not evidence that the pins or electrical requirements match.
Keep electrical requirements beside the physical sample
Add the verified pinout, polarity, voltage and required cable specification for each candidate from its own product documents. Mark unknown details as unresolved rather than copying them from a neighbouring sample. Before choosing a harness, confirm the actual mating parts and complete assembly requirements with the supplier; update the board when a part changes.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Can a connector that physically mates be treated as compatible?
No. A physical fit does not confirm pin assignments, polarity, voltage or suitable cable capacity. Verify these independently and check the whole lighting arrangement before connecting power. The board documents candidates; it is not an adapter design or an approval for mixing different suppliers’ systems.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Browse the complete LED Modules range below. Send the lightbox depth, connector photos, verified pinout and intended supply arrangement to discuss suitable bars and confirm current product specifications before purchase.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
EM Plastic serves Canada’s sign and display industry and hosts supplier open houses. For lightbox builders comparing internal LED components around these activities, this selection focuses on an unpowered connector sample board: a practical record of the connections being considered before ordering bars and harness parts.
Compare connector samples without applying power
Attach clearly identified loose connector samples or photographs to a comparison board. Record the supplier part reference, housing shape, latch position and mating direction. Keep the board unpowered and separate from a working circuit. Similar-looking connectors are comparison candidates, not evidence that the pins or electrical requirements match.
Keep electrical requirements beside the physical sample
Add the verified pinout, polarity, voltage and required cable specification for each candidate from its own product documents. Mark unknown details as unresolved rather than copying them from a neighbouring sample. Before choosing a harness, confirm the actual mating parts and complete assembly requirements with the supplier; update the board when a part changes.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Can a connector that physically mates be treated as compatible?
No. A physical fit does not confirm pin assignments, polarity, voltage or suitable cable capacity. Verify these independently and check the whole lighting arrangement before connecting power. The board documents candidates; it is not an adapter design or an approval for mixing different suppliers’ systems.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Browse the complete LED Modules range below. Send the lightbox depth, connector photos, verified pinout and intended supply arrangement to discuss suitable bars and confirm current product specifications before purchase.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.