Choosing LED bars for a fabric lightbox tower at the Transcatheter Cardiovascular Therapeutics Conference, commonly called TCT? Compare internal lightbox sources for printed booth graphics and specify the illuminated faces around meeting areas and canopies.
Which LEDs suit a TCT fabric lightbox tower?
Start with the illuminated face dimensions, clear frame depth and source mounting positions. Check the final fabric with pale backgrounds, fine lettering and diagram details at the intended white tone. Compare edge-lit and rear-backlit arrangements using the actual frame section; tower height or bar wattage alone cannot establish quantity or even illumination.
Will canopies and meeting-room walls affect the lightbox?
Mark canopy edges, structural supports and adjacent hard walls on the drawing. They can change viewing angles or obstruct an illuminated face. Check the assembled tower from the aisle and meeting entrance, and test each differently shaped face with its actual print. Leave access to wiring after the adjoining structures are installed.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Can fabric lightboxes and halo-lit logos use the same LED layout?
They need separate layouts. A printed fabric face transmits light across a broad surface; a raised halo-lit logo projects light onto the surrounding surface. Compare mounting space, optical direction and electrical load for each application. These product recommendations concern internal graphic-lightbox sources; they do not specify a halo-letter system.
Before ordering
For the three featured bars: Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Compare all 26 products below. Send labelled tower sections, fabric samples, canopy positions and wiring-access drawings for an LED component quote. State the desired white tone and power arrangement. The LED bars do not include fabric, tower frames or meeting-room structures.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
Choosing LED bars for a fabric lightbox tower at the Transcatheter Cardiovascular Therapeutics Conference, commonly called TCT? Compare internal lightbox sources for printed booth graphics and specify the illuminated faces around meeting areas and canopies.
Which LEDs suit a TCT fabric lightbox tower?
Start with the illuminated face dimensions, clear frame depth and source mounting positions. Check the final fabric with pale backgrounds, fine lettering and diagram details at the intended white tone. Compare edge-lit and rear-backlit arrangements using the actual frame section; tower height or bar wattage alone cannot establish quantity or even illumination.
Will canopies and meeting-room walls affect the lightbox?
Mark canopy edges, structural supports and adjacent hard walls on the drawing. They can change viewing angles or obstruct an illuminated face. Check the assembled tower from the aisle and meeting entrance, and test each differently shaped face with its actual print. Leave access to wiring after the adjoining structures are installed.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Can fabric lightboxes and halo-lit logos use the same LED layout?
They need separate layouts. A printed fabric face transmits light across a broad surface; a raised halo-lit logo projects light onto the surrounding surface. Compare mounting space, optical direction and electrical load for each application. These product recommendations concern internal graphic-lightbox sources; they do not specify a halo-letter system.
Before ordering
For the three featured bars: Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Compare all 26 products below. Send labelled tower sections, fabric samples, canopy positions and wiring-access drawings for an LED component quote. State the desired white tone and power arrangement. The LED bars do not include fabric, tower frames or meeting-room structures.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.