Planning an independent PPMA Show stand where a printed lightbox introduces a product programme beside equipment samples? Compare all 26 LED Modules products for the graphic's internal lighting. Review the relationship between the message and the selected samples before approving the print.
Map each printed category to its displayed sample
Make a list linking each programme name or equipment category on the lightbox to the sample visitors can inspect. Identify categories without a displayed example and make their intended meaning explicit in the artwork. Check the final wording with the exhibitor; a programme graphic should not suggest every nearby machine has the same availability or specification.
Repeat the message check when the sample selection changes
Review the mapping after a sample is removed or substituted. Update affected labels or artwork before retesting that print on the recorded LED layout. Keep the content approval separate from the lightbox's uniformity check so that a technically acceptable face is not mistaken for an accurate product message. Retain the accepted sample list, artwork revision and lighting configuration together.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Are these modules lights for machinery inspection or magnetic separation?
No. They light printed exhibition graphics inside independently designed lightboxes. The event context does not qualify them for process equipment, inspection systems or a machine's electrical installation. Confirm the display frame and component requirements separately.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the lightbox section, programme artwork, category-to-sample list and accepted print revision to discuss an LED source trial.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
Planning an independent PPMA Show stand where a printed lightbox introduces a product programme beside equipment samples? Compare all 26 LED Modules products for the graphic's internal lighting. Review the relationship between the message and the selected samples before approving the print.
Map each printed category to its displayed sample
Make a list linking each programme name or equipment category on the lightbox to the sample visitors can inspect. Identify categories without a displayed example and make their intended meaning explicit in the artwork. Check the final wording with the exhibitor; a programme graphic should not suggest every nearby machine has the same availability or specification.
Repeat the message check when the sample selection changes
Review the mapping after a sample is removed or substituted. Update affected labels or artwork before retesting that print on the recorded LED layout. Keep the content approval separate from the lightbox's uniformity check so that a technically acceptable face is not mistaken for an accurate product message. Retain the accepted sample list, artwork revision and lighting configuration together.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Are these modules lights for machinery inspection or magnetic separation?
No. They light printed exhibition graphics inside independently designed lightboxes. The event context does not qualify them for process equipment, inspection systems or a machine's electrical installation. Confirm the display frame and component requirements separately.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the lightbox section, programme artwork, category-to-sample list and accepted print revision to discuss an LED source trial.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.